Rapid Fire Products

STRAIGHT GRIP WINCHESTER 92 POST 64 STOCK & FOREND WALNUT SATIN FINISH BOYDS PLASTIC BUTT PLATE STOCK It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 15/16" Top Tang Length: 3 15/16" Bottom Tang Width: 5/8" Bottom Tang Length: 3 15/16" Stock Height at Receiver: 1 7/16" Stock Width at Receiver: 1 5/16" Overall Length of Stock:13 1/4" Measurement of Receiver Mounting Bolt: N/A Comes with Boyds' plastic buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel at Receiver: Approximately 1" Barrel Channel at End: 11/16" Receiver Edge to Center of Mounting Screw: 6 7/8" Shoulder to Shoulder: 6 11/16"Overall Length of Part : 7 3/16" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

LH PLAT BROWNING AB2 SSA 2PC HINGED FLOOR PLATE LH STK FBC PEPPER SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1.176" and Point B = .842"Center to Center of Action Screws: 6.66"Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need the floor plate, take down screws, trigger guard and screw from your factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a . All Rapid Fire sales are final! Nonreturnable & nonrefundable.

LH FT REMINGTON 783 LA LH STK RH ACT DBM FBC NUTMEG SATIN FINISH BOYDS PAD ATTENTION CUSTOMERS: DENTED TIP Barrel Dimensions: Point A = 1 5/64" and Point B = 3/4"Center to Center of Action Screws: 7 31/32"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.Safety and Bolt Release are located on the side of the receiver.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final!

RIMFIRE HUNTER CZ 452-2E AMERICAN SA CLIP FEED LH ACT FBC PEPPER SATIN FINISH BOYDS PAD ATTENTION CUSTOMERS: SCRATCHES AND DENTS ON BUTTSTOCK, BOTH SIDES. Barrel Dimensions: Point A = .99" and Point B = .712"Center to Center of Action Screws: 3.235"Over All Length of Part: 31.25"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need floor plate, take down screws, trigger plate and clip from the factory stock. ATTENTION CUSTOMERS: Not compatible with ZKM model variations. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

LH FT SAVAGE 112 TBR BLIND MAG STFG LH STK RH ACT FBC Forest Camo Satin Finish Boyds Pad ATTENTION CUSTOMERS: Bubbles in the finish on comb. Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page. This stock is designed for the Savage Model Blind Magazine with Staggered Feed action and a top bolt release. When you disassemble your action the magazine box will be attached to the receiver. If the magazine box stays inside of the stock when the barreled action is removed, you may need the Center Feed Model or CTF version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

HERT REMINGTON 700 SA DBM HAWKINS PRECISION M5 FBC Black Textured Paint Boyds Pad ATTENTION CUSTOMERS: Dented cheek piece Barrel Channel Dimensions: Point A - 1 1/4" Point B - 3/4" Center to Center Action Screws: 6 1/2" Comes with Boyds 1/2" recoil pad. ATTENTION CUSTOMERS: This inlet is machined to accept the Hawkins Precision M5 Detachable Box Magazine Short Action Bottom Metal. You will need to purchase the Hawkins Precision M5 Bottom Metal separately. Inlet is not milled for Hawkins pillars due to end user preference. Refer to Hawkins Precision for specifics of the M5 Detachable Box Magazine. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

SPIKE CAMP SAVAGE 93 LEFT HAND ACTION, BULL BARREL CHANNEL Forest Camo Satin Finish Boyds Pad Barrel Dimensions: Point A = 13/16" and Point B = 13/16" Center to Center of Action Screws: 3 11/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: This stock is designed for the Sav93-E/MKII heavy barrel with inlet trigger guard and floor plate. Action measures 7 3/4" long on the 93E/MKII action. Pre-93E receivers (with a lug at the back of the reciever) can be fit to our 93E/MKII stocks but will require fitting of your receiver and barrel to the stock. Minor gap will be visible on rear of stock with older pre-accutrigger actions. Older receivers are about 4 inches longer and will need to be fit. Variations in action mounting screw pillars exist between models. Do not over tighten. ATTN customers: Side mount rear peep sights will require modifications of the stock for fitment. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page, bottom left-hand corner. Part numbers for 22 LR: 100654 (Blued), 100655 (Nickel). Part numbers for 17hmr/22mag: 100656 (Blued), 100657 (Nickel). Some stocks may also require different action screws which are available through DiProductsInc: PN 13020. Variations in action mounting screw pillars exist between models. Do not over tighten. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

HERT STEYR PRO HUNTER #3 LA DBM FBC PEPPER SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1 1/64" and Point B = 45/64" Center to Center of Action Screws: 4 29/32" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This inlet is for the Pre 2024 models that have the magazine liner attached to the action. We will be You will need the front takedown screw from your stock. We will be providing the trigger guard, trigger guard screw, and rear takedown screw.. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

SPIKE CAMP SAVAGE 111 SIDE RELEASE DBM LA FBC COYOTE HIGH GLOSS BOYDS PAD It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Barrel Dimensions: Point A = 1 21/64" and Point B = 23/32"Center to Center of Action Screws: 5 1/16”Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS:  This inlet is for the side release magazine version. You will need your trigger guard with screws and side release button.  All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

CLA ARISAKA TYPE 99 LONG ACTION, MILITARY BARREL CHANNEL SHADY CAMO SATIN FINISH LIMBSAVER PAD LASER PANEL BLACK GRIP CAP BLACK TIP CAP It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions: Point A = 1 17/64" and Point B = 47/64"Center to Center of Action Screws: 6 61/64"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS: You will need the takedown screws, floorplate, and magazine from the original stock. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

PLAT SAV 10 SHORT ACTION DETACHABLE MAGAZINE BULL BARREL CHANNEL NUTMEG HIGH GLOSS BOYDS PAD LASER PANEL PILLAR BEDDING Barrel Dimensions: Point A = 1 1/8" Point B = 1 1/16" Center to Center Action Screws: 4 7/16" Overall Length of Part: N/A Comes with Boyds 1/2" Recoil Pad. ATTENTION CUSTOMERS: You will need your factory Floor Plate, Action Screws and Detachable Box Mag. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with bottom bolt release (located on the front of the trigger guard). The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock. ATTENTION CUSTOMERS: If you have an Apex Hunter model it will not be a direct fit in this stock, as it will require modifying the trigger area for clearance due to differences in the trigger mechanism.ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212.. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

HERT BROWNING A-BOLT MICRO SA FBC WALNUT SATIN FINISH BOYDS PAD It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions: Point A = 1 11/64" and Point B = 43/64"Center to Center of Action Screws: 7 13/64"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS: Before you order, you must confirm, by serial number, if your firearm model is an A-Bolt, A-Bolt II (2), or A-Bolt III (3). The roll stampings on all versions only states A-Bolt regardless of model. Also, you will need to confirm if your particular firearm is a Micro version or not. Micro versions are different than the standard models. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect All Rapid Fire sales are final! Nonreturnable & nonrefundable.

REM 11 TYPE 3 12 GA STOCK & FOREND CLARO XX WALNUT SATIN FINISH BOYDS BUTT PLATE ATTENTION CUSTOMERS: FOREND IS LIGHTER STAIN THAN BUTTSTOCK STOCK It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 5/8" Top Tang Length: 3 5/16" Bottom Tang Width: 9/16" Bottom Tang Length: 2 7/8" Stock Height at Receiver: 1 3/4" Stock Width at Receiver: 1 9/16" Overall Length of Stock:13 1/2" Comes with Boyds' Black Plastic Buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: N/A Barrel Channel Point B: N/A Magazine Tube Width: N/A Recoil Spring cut out measures 7 9/16" from front receiver Over All Length of Part: 11 1/8" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS: These forends do not come with forward Cap retaining spring. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

AP REM 1100 12 GA STOCK & FOREND XX WALNUT SATIN FINISH PACHMAYR PAD FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: N/A Barrel Channel Point B: N/A Receiver Edge to Center of Mounting Screw/Magazine Tube Width: 1 9/16 " Magazine Tube Shoulder to Shoulder: N/A Over All Length of Part: 11 3/4 All finished parts have been CNC inlet to Boyds' House Action. Variations exist on these forends including that may require minor fitting to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect STOCK It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Top Tang Width: N/ATop Tang Length: N/ABottom Tang Width: 9/16"Bottom Tang Length: 9/16"Stock Height at Receiver: 2"Stock Width at Receiver: 1 7/16"Overall Length of Stock: 13 3/4"Measurement of Receiver Mounting Bolt: 10 1/2"Comes with Pachmayr recoil pad All Rapid Fire sales are final! Nonreturnable & nonrefundable.

WEATHERBY SA-08 12GA FOREND & BUTTSTOCK FOREST CAMO SATIN FINISH VENTED BOYDS PAD STOCK Bottom Tang Width: 33/64" Bottom Tang Length: 3/8" Stock Height at Receiver: 2" Stock Width at Receiver: 1 1/2" Overall Length of Stock: 13 3/4" Measurement of Receiver Mounting Bolt: 1 1/2" It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. FOREND Barrel Channel Point Rear: 1 9/64" Barrel Channel Point Front: 27/32" Magazine Tube Width: 1 5/16" Receiver Face to Mag Tube Mounting Shoulder: 9 39/64" Over All Length of Part: 12 3/32" It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

FT SAV 110 TACTICAL AICS MAG HEAVY BARREL CHANNEL SHADY CAMO SATIN FINISH BOYDS PAD LASER PANEL ANGLED WALNUT TIP CAP PILLAR BEDDING Barrel Dimensions: Point A = 1 1/16" and Point B = 14/16" Center to Center of Action Screws: 4 7/16" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: You will need to order the Savage Screw Set from the Accessories page(PART #: 100010). This stock is designed for the Savage 110 Tactical model that utilizes an AICS platform and has a heavy barrel. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

LH FT TIKKA T3 DBM LH STOCK RH ACT FBC PEPPER SATIN FINISH BOYDS PAD LOP 13 1/4" Barrel Dimensions: Point A = 1 7/64" and Point B = 45/64" Center to Center of Action Screws: 4 5/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. The Safety is located on the tang and the Bolt Release is on the side of the receiver. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

PH BROWNING X-BOLT SA LH STK LH ACT FBC PEPPER SATIN FINISH PACHMAYR PAD LOP 13 1/4" Barrel Dimensions: Point A = 1 7/64" and Point B = 45/64" Center to Center of Action Screws: 4 5/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. The Safety is located on the tang and the Bolt Release is on the side of the receiver. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

Heritage, Browning® A-bolt, Short Action, Factory Barrel Channel WALNUT SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4" Center to Center of Action Screws: 7 1/4" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Boyds' has designed the Browning A-Bolt stocks so you do not have to use the rear metal shim that is supplied by Browning for some models. These parts are manufactured using standard Browning short - action receivers. They are not intended for Micro-medallion series or any WSSM action. Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II, or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO Versions are different than standard models. Call Browning Customer Service for more information. All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

PH MOSSBERG MVP DBM SA FBC APPLE JACK SATIN FINISH BOYDS PAD ADJUSTABLE COMB Barrel Dimensions: Point A = 1" and Point B = 45/64" Center to Center of Action Screws: 4 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: You will need your magazine liner, trigger guard with screw, takedown bolts, and take down bolt head washer. ATTENTION: Not compatible with LR Tactical with AR-Style Magazine. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

WIN 94 POST 64 STOCK & BARREL BAND FOREND CLARO XX WALNUT ELITE FINISH BOYDS PLASTIC BUTT PLATE FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel at Receiver: Approximately 1" Barrel Channel at End: 11/16" Receiver Edge to Center of Mounting Screw: 6 7/8" Shoulder to Shoulder: 6 11/16"Overall Length of Part : 7 3/16" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. STOCK It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 1 1/32" Top Tang Length: 3 7/8" Bottom Tang Width: 9/16" Bottom Tang Length: 3 15/16" Stock Height at Receiver: 1 5/16" Stock Width at Receiver: 1 3/8" Overall Length of Stock:13 1/4" BOYDS' PLASTIC BUTTPLATE All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:Due to variations with this model minor fitting of the receiver may be needed even with these finished parts. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

SPIKE CAMP SEEKINS PRECISION HAVAK LONG ACTION DBM FBC FOREST CAMO SATIN FINISH BOYDS PAD LASER PANEL Barrel Channel Point A: 1 1/4" Point B 7/8" Center to Center Action Screws: 7 3/8" It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: You will need the floor plate, action screws, and mag box from your factory stock. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

LH CLA BROWNING A-BOLT SHORT ACTION LEFT HAND STOCK RIGHT HAND ACTION FBC WALNUT HIGH GLOSS BOYDS PAD Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4"Center to Center of Action Screws: 7 1/4"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS:Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out;Browning;for more info.All finished stocks have been CNC inlet to Boyds House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

SPIKE CAMP SAVAGE 93E MKII LEFT HAND ACTION BULL BARREL CHANNEL PEPPER SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 13/16" and Point B = 13/16" Center to Center of Action Screws: 3 11/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: This stock is designed for the Sav93-E/MKII heavy barrel with inlet trigger guard and floor plate. Action measures 7 3/4" long on the 93E/MKII action. Pre-93E receivers (with a lug at the back of the reciever) can be fit to our 93E/MKII stocks but will require fitting of your receiver and barrel to the stock. Minor gap will be visible on rear of stock with older pre-accutrigger actions. Older receivers are about 4 inches longer and will need to be fit. Variations in action mounting screw pillars exist between models. Do not over tighten. ATTN customers: Side mount rear peep sights will require modifications of the stock for fitment. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page, bottom left-hand corner. Part numbers for 22 LR: 100654 (Blued), 100655 (Nickel). Part numbers for 17hmr/22mag: 100656 (Blued), 100657 (Nickel). Some stocks may also require different action screws which are available through DiProductsInc: PN 13020. Variations in action mounting screw pillars exist between models. Do not over tighten. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

PV CZ 550 DBM SA BBC Black Textured Paint Limbsaver Pad Laser Panel LOP 14" Barrel Dimensions: Point A = 1 7/64" and Point B = 55/64" Center to Center of Action Screws: 7 13/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & Nonreturnable.

Hert Rem 700 SA Detachable Mag FBC Black Textured Paint Boyds Pad Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4" Center to Center of Action Screws: 6 1/2" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is inlet for the standard factory tapered barrel. These stocks are designed for the Remington 700 receiver with factory supplied detachable box magazine. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable and nonreturnable.

PV CZ 550 DBM SA BBC Nutmeg High Gloss Limbsaver Pad Laser Panel ATTENTION CUSTOMERS: VISIBLE SANDING MARKS THROUGHOUT STOCK, SCUFF ON RIGHT HAND SIDE OF BUTTSTOCK, LITTLE DENT RH SIDE OF FOREND, FINISH FLAW ON BOTTOM OF BUTT, NATURAL WOOD FLAWS BELOW BOLT CUT, AND OPPOSITE SIDE OF FOREND. Barrel Dimensions: Point A = 1 7/64" and Point B = 55/64" Center to Center of Action Screws: 7 13/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

SPIKE CAMP THUMBHOLE, SAVAGE® 93 BOLT ACTION, LEFT HAND ACTION, BULL BARREL CHANNEL SHADY CAMO SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 13/16" and Point B = 13/16" Center to Center of Action Screws: 3 11/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: This stock is designed for the Sav93-E/MKII heavy barrel with inlet trigger guard and floor plate. Action measures 7 3/4" long on the 93E/MKII action. Pre-93E receivers (with a lug at the back of the reciever) can be fit to our 93E/MKII stocks but will require fitting of your receiver and barrel to the stock. Minor gap will be visible on rear of stock with older pre-accutrigger actions. Older receivers are about 4 inches longer and will need to be fit. Variations in action mounting screw pillars exist between models. Do not over tighten. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page, bottom left-hand corner. Part numbers for 22 LR: 100654 (Blued), 100655 (Nickel). Part numbers for 17hmr/22mag: 100656 (Blued), 100657 (Nickel). Some stocks may also require different action screws which are available through DiProductsInc: PN 13020. Variations in action mounting screw pillars exist between models. Do not over tighten. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

SPIKE CAMP SAV 110 BBR DETACHABLE MAG LONG ACTION LH ACT FBC SKY SATIN FINISH BOYDS PAD PILLAR BEDDING Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage detachable box magazine rifle with bottom bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock.ATTENTION CUSTOMERS: Attention Customer: If you have an Apex Hunter model it will not be a direct fit in this stock, as it will require modifying the trigger area for clearance due to differences in the trigger mechanism. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE LA PLASTIC MAG WELL from our Accessories page, Part No. A09160 or SAVAGE LA METAL MAG WELL, Part No. A09213. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from the Accessories page, SAVAGE LA PLASTIC MAG WELL, part no. A09160. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final!

CLA SAKO 75-1 HUNTER SA FBC CLARO X WALNUT SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1.042" and Point B = .707"Center to Center of Action Screws: 6.683" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need floor plate, take down screws, and mag box from the factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

AMERICAN PLAINSMAN REMINGTON 870 12GA STOCK Nutmeg ATTENTION CUSTOMERS: 10 1/2" factory stock bolt is required for this buttstock. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Top Tang Width: N/ATop Tang Length: N/ABottom Tang Width: 1/2"Bottom Tang Length: 5/8"Stock Height at Receiver: 1 15/16"Stock Width at Receiver: 1 1/2"Overall Length of Stock: 13 3/4"Measurement of Receiver Mounting Bolt - 10 1/2Comes with Pachmay Decelerator recoil padAll finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.ATTENTION CUSTOMERS: These stocks are designed for the larger frame models. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

AMERICAN PLAINSMAN REMINGTON 870 12GA STOCK Pepper ATTENTION CUSTOMERS: 10 1/2" factory stock bolt is required for this buttstock. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Top Tang Width: N/ATop Tang Length: N/ABottom Tang Width: 1/2"Bottom Tang Length: 5/8"Stock Height at Receiver: 1 15/16"Stock Width at Receiver: 1 1/2"Overall Length of Stock: 13 3/4"Measurement of Receiver Mounting Bolt - 10 1/2"Comes with Pachmay Decelerator recoil padAll finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.ATTENTION CUSTOMERS: These stocks are designed for the larger frame models. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

AMERICAN PLAINSMAN REMINGTON 870 12GA STOCK Walnut It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need to purchase the 8 5/16" mounting bolt for wood stocks from the Accessories page, Part Number: A09168.Top Tang Width: N/ATop Tang Length: N/ABottom Tang Width: 1/2"Bottom Tang Length: 5/8"Stock Height at Receiver: 1 15/16"Stock Width at Receiver: 1 1/2"Overall Length of Stock: 13 3/4"Measurement of Receiver Mounting Bolt - 8 5/16"Comes with Pachmay Decelerator recoil padAll finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.ATTENTION CUSTOMERS: These stocks are designed for the larger frame models. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

FT WIN 70 PRE-64 LA 2PC FP FBC Black Jack Satin Finish Limbsaver Pad Laser Symbol: Wolf Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4" Center to Center of Action Screws: 7 7/16" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS: These stocks are designed for the Winchester model 70 pre 64 long action, with a 2 piece floor plate, factory barrel. You will need your factory Trigger Guard, 2-Piece Hinged Floor Plate, 3 Action Screws, Machine Screw w/escutcheon(Forend Location) & Magazine Box. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

PLAT REM 700 LA 1PC FP LH STOCK RH ACT BBC Walnut Satin Finish Pachmayr Pad Laser Panel Pillar Bedding Barrel Dimensions: Point A = 1.245" and Point B = 0.9"Center to Center of Action Screws: 7.345" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS:You will need the floor plate, mag box, and take down screws from your factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

Savage® 67 (top Rec Safety) Stock WALNUT UNFINISH BOYDS BUTTPLATE These parts are designed to fit the Savage,Stevens,Springfield and Fox models 30,67,77,79,168 and 176 stocks with top receiver safety, please compare your stock and receiver measurements with those we supply.Make sure to confirm demensions with those supplied for this parts. There may be up to five variations of this model.Top Tang width - 9/16ths"Top Tang length - 1 7/16ths"BottomTang width - 5/8ths"BottomTang length - 1 5/16ths"Stock height at receiver -1 5/8ths"Stock width at receiver -1 1/2" Semi-inlet parts have been comletely shaped and 95% machine inlet. Stocks are rough sanded and unless otherwise specified, are shipped with a BOYDS' butt plate.(SEMI-INLET) stocks do require some knowledge of firearms and woodworking for installation. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

PH BROWNING A-BOLT SHORT ACT FBC NUTMEG HIGH GLOSS BOYDS PAD ANGLED BLACK TIP BLACK GRIP CAP LASER INITIALS: LEA FONT #2 Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4"Center to Center of Action Screws: 7 1/4"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info.All finished stocks have been CNC inlet to Boyds House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

HERITAGE MOSSBERG 100 ATR SA FBC XX MAPLE HIGH GLOSS WHITE LINE SPACER BOYDS PAD BLACK GRIP CAP LASER PANEL ATTENTION CUSTOMERS: Visible sanding marks throughout stock. Slight dent on comb. Barrel Dimensions: Point A = 1 3/8" and Point B = 13/16" Center to Center of Action Screws: 4 9/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: If you are converting from a plastic stock, you will need to purchase a trigger guard from our Accessories page: ITEM # A09157, and an action screw from Mossberg directly, ITEM # 101532. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

FT MOSSBERG 4X4 DBM LA FBC ROYAL SATIN FINISH BOYDS PAD ATTENTION CUSTOMERS: SCRATCH ON RIGHT SIDE OF STOCK ABOVE MAGWELL, WOOD FILL MISSED NEAR SAME AREA Barrel Dimensions: Point A = 1 11/64" and Point B = 23/32" Center to Center of Action Screws: 5 15/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. The Safety and Bolt Release are on the side of the receiver. ATTENTION CUSTOMERS: OUR STOCK WILL ONLY WORK FOR THE PLASTIC/SYNTHETIC TO WOOD CONVERSION. You will need to use the plastic mag liner from the original factory stock and the front action screw (.930"). Each stock will be supplied with the rear action screw (1.5"), "FLAT FRONT" trigger guard, and wood screw (1"). It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

SPIKE CAMP WIN 70 SA 2PC FP FBC POST 64 Royal Jacaranda Satin Finish Boyds Pad Laser Panel Pillar Bedding Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 29 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock will not work for the WSSM Caliber Rifles. Pre-1984 actions are based on the Long Action receiver. These stocks are designed for the Winchester Model 70 Short Action 2-Piece hinged floor plate model with a standard factory tapered barrel. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.