Rapid Fire Products

PH CZ 550 AMERICAN LONG ACTION FBC PEPPER SATIN FINISH BOYDS PAD ATTENTION CUSTOMERS: FINISH FLAWS AND DENTS ON COMB It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Barrel Dimensions: Point A = 1 7/64" and Point B = 47/64"Center to Center of Action Screws: 7 53/64”Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS:  You will need your takedown screws, floor plate assembly, and mag well. All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

FT MOSSBERG 4X4 DBM LA FBC ROYAL SATIN FINISH BOYDS PAD ATTENTION CUSTOMERS: SCRATCH ON RIGHT SIDE OF STOCK ABOVE MAGWELL, WOOD FILL MISSED NEAR SAME AREA Barrel Dimensions: Point A = 1 11/64" and Point B = 23/32" Center to Center of Action Screws: 5 15/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. The Safety and Bolt Release are on the side of the receiver. ATTENTION CUSTOMERS: OUR STOCK WILL ONLY WORK FOR THE PLASTIC/SYNTHETIC TO WOOD CONVERSION. You will need to use the plastic mag liner from the original factory stock and the front action screw (.930"). Each stock will be supplied with the rear action screw (1.5"), "FLAT FRONT" trigger guard, and wood screw (1"). It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

FT WIN 70 SHORT ACTION 2-PC FLOOR PLATE FBC POST 64 SKY HIGH GLOSS LIMBSAVER PAD ATTENTION CUSTOMERS: FINISH FLAWS THROUGHOUT STOCK - SCRATCHES, BLEMISHES Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. THIS STOCK WILL NOT WORK FOR THE WSSM CALIBER RIFLES. PRE 1984 ACTIONS ARE BASED ON THE LONG ACTION RECEIVER. THESE STOCKS ARE DESIGNED FOR THE WINCHESTER® MODEL 70 SHORT ACTION 2-PIECE HINGED FLOOR PLATE MODEL, WITH STANDARD FACTORY TAPERED BARREL. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & norefundable.

CZ® 457, AGILITY, FBC Royal Adjustable Comb Barrel dimensions: Point A = 7/8" Point B = 7/8" Center to center action screws: N/A ATTENTION: You will need take down screws from the factory stock. We will provide the lug. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS : If you are switching from a synthetic stock with no removable floorplate you will need to purchase an aftermarket trigger guard floorplate assembly to complete your build. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

AGILITY, REMINGTON 700 ADL, SHORT ACTION, FACTORY BARREL CHANNEL, Maroon High Gloss Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4" Center to Center of Action Screws: 6 1/2" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is inlett for standard factory tapered barrel channel and is designed for the Remington 700 right hand short action with blind magazine, loads and unloads through top of action. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

AT-ONE SAVAGE® 93 BOLT ACTION, CLIP FEED, LEFT HAND ACTION, BULL BARREL CHANNEL Walnut ATTENTION CUSTOMERS: IMAGE IS A 'STOCK' IMAGE, BOLT CUT IS ON THE LEFT SIDE.  Barrel Dimensions: Point A = 13/16" and Point B = 13/16" Center to Center of Action Screws: 3 11/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Sav93-E/MKII heavy barrel with inlet trigger guard and floor plate. Action measures 7 3/4" long on the 93E/MKII action. Pre-93E receivers (with a lug at the back of the reciever) can be fit to our 93E/MKII stocks but will require fitting of your receiver and barrel to the stock. Minor gap will be visible on rear of stock with older pre-accutrigger actions. Older receivers are about 4 inches longer and will need to be fit. Variations in action mounting screw pillars exist between models. Do not over tighten. ATTN customers: Side mount rear peep sights will require modifications of the stock for fitment. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page, bottom left-hand corner. Part numbers for 22 LR: 100654 (Blued), 100655 (Nickel). Part numbers for 17hmr/22mag: 100656 (Blued), 100657 (Nickel). Some stocks may also require different action screws which are available through DiProductsInc: PN 13020. Variations in action mounting screw pillars exist between models. Do not over tighten. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

AT-ONE, REMINGTON® 700 BDL, LONG ACTION, FACTORY BARREL CHANNEL, LH ACTION, Pepper Barrel Dimensions: Point A = 1 1/4" and Point B = 25/32" Center to Center of Action Screws: 7 3/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Inlett for standard factory tapered barrel channel. This stock is designed for the Remington 700 LEFT Hand Long Action with hinged floor plate. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

AT-ONE THUMBHOLE KIMBER 8400 SA FBC Royal Jacaranda It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Barrel Dimensions: Point A = 1 17/64" and Point B = 23/32"Center to Center of Action Screws: 6 43/64”Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and mag box from the original stock.All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

AT-ONE THUMBHOLE SAVAGE 110 BBR DETACHABLE MAG LA Royal Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage detachable box magazine rifle with bottom bolt release (located on the front of the trigger guard). The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock.ATTENTION CUSTOMERS: Attention Customer: If you have an Apex Hunter model it will not be a direct fit in this stock, as it will require modifying the trigger area for clearance due to differences in the trigger mechanism. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE LA PLASTIC MAG WELL from our Accessories page, Part No. A09160 or SAVAGE LA METAL MAG WELL, Part No. A09213. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from the Accessories page, SAVAGE LA PLASTIC MAG WELL, part no. A09160. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

AGILITY BERGARA BMR 22LR MAGAZINE FEED FACTORY BARREL CHANNEL Sky Adjustable Comb Pillar Bedding ATTENTION CUSTOMERS: MISMATCHED COMB - BLUE IS SLIGHTLY DIFFERENT FROM STOCK Barrel Dimensions: Point A = 1" and Point B = 3/4" Center to Center Action Screws: 5 7/8"ATTENTION CUSTOMERS: You will need your floor plate, front & rear action screws, and mag box. This stock was designed for the steel barrel version, not compatible with carbon barrel. It is your reponsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

AT-ONE THUMBHOLE KIMBER 8400 SA FBC Walnut It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Barrel Dimensions: Point A = 1 17/64" and Point B = 23/32"Center to Center of Action Screws: 6 43/64”Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and mag box from the original stock.All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

AT-ONE THUMBHOLE SAVAGE AXIS DBM LA FBC Apple Jack Pillar Bedding Barrel Dimensions: Point A = 1 11/32"; and Point B = 23/32" ATTENTION CUSTOMERS: For long action calibers; 25-06 REM, 30-06 SPFLD, or 270 WIN. When assembling, hold the barrel in the center of the channel and tighten screws. Length of Mag Box: 3 49/64" Center to Center of Action Screws: 4 25/32"; Over All Length of Part: 31 1/2" Comes with Boyds 1/2" Rubber Recoil Pad. Safety is located on the tang and the Bolt Release is on the side of the receiver. A black plastic trigger guard, screw, front mag tab, rear mag tab, and recoil lug are included with the stock. ;***Stainless Steel Metal trigger guards are also available: PN 100662. They can be found on the Accessories page.***ATTENTION CUSTOMERS: This stock is compatible with the Savage Axis II and Axis XP models. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds #39; House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

AT-ONE THUMBHOLE, SAVAGE® 93 BOLT ACTION, CLIP FEED, LEFT HAND ACTION, BULL BARREL CHANNEL Coyote ATTENTION CUSTOMERS: IMAGE IS A 'STOCK' IMAGE, BOLT CUT IS ON THE LEFT SIDE.  Barrel Dimensions: Point A = 13/16" and Point B = 13/16" Center to Center of Action Screws: 3 11/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Sav93-E/MKII heavy barrel with inlet trigger guard and floor plate. Action measures 7 3/4" long on the 93E/MKII action. Pre-93E receivers (with a lug at the back of the reciever) can be fit to our 93E/MKII stocks but will require fitting of your receiver and barrel to the stock. Minor gap will be visible on rear of stock with older pre-accutrigger actions. Older receivers are about 4 inches longer and will need to be fit. Variations in action mounting screw pillars exist between models. Do not over tighten. ATTN customers: Side mount rear peep sights will require modifications of the stock for fitment. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page, bottom left-hand corner. Part numbers for 22 LR: 100654 (Blued), 100655 (Nickel). Part numbers for 17hmr/22mag: 100656 (Blued), 100657 (Nickel). Some stocks may also require different action screws which are available through DiProductsInc: PN 13020. Variations in action mounting screw pillars exist between models. Do not over tighten. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

AGILITY, WEATHERBY VANGUARD, SHORT ACTION, BULL BARREL CHANNEL, Pepper Laser Panel Adjustable Comb Barrel Dimensions: Point A = 1 1/4" and Point B = 1" Center to Center of Action Screws: 7 1/4" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:This stock is designed for the Weatherby Vanguard Short Action, with factory Varmint Contour. Numerous other models have been manufactured using this action design. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

LH FT BROWNING A-BOLT LH STK RH ACT FBC Pepper Satin Finish Boyds Pad Laser Symbol: Wolf Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4" Center to Center of Action Screws: 7 1/4" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info. All finished stocks have been CNC inlet to Boyds House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

LH PLAT Ruger Gunsite Scout Short Act Left Hand Stock Right Hand Act DBM Forest Camo Satin Finish Boyds Pad Adjustable Comb Barrel Dimensions: Point A = 1 5/32" and Point B = 3/4" Center to Center of Action Screws: 6 45/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: If you are purchasing this stock as a replacement to a Polymer Stocked GSR, you will need to purchase or acquire a bottom metal kit to complete the build. You will need your takedown screws, trigger guard, mag box assembly, forward takedown/mag box retainer, and magazine.ATTENTION CUSTOMERS: We do not machine or provide for the factory threaded cross bolt behind the mag well on this model. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

LH FT REM 700 BDL LA RIGHT HAND STK LEFT HAND ACT FBC PEPPER HIGH GLOSS BOYDS PAD ATTENTION CUSTOMERS: DENTED BY THE PAD ON RIGHT SIDE Barrel Dimensions: Point A = 1 1/4" and Point B = 25/32" Center to Center of Action Screws: 7 3/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Inlett for standard factory tapered barrel channel. This stock is designed for the Remington 700 LEFT Hand Long Action with hinged floor plate. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

HERT KIMBER 8400 SA FBC SKY SATIN FINISH BOYDS PAD It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Barrel Dimensions: Point A = 1 17/64" and Point B = 23/32"Center to Center of Action Screws: 6 43/64”Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and mag box from the original stock.All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

SPIKE CAMP LITHGOW LA102 SA DBM FBC FOREST CAMO SATIN FINISH BOYDS PAD Barrel Channel Dimensions: Point A - 1 1/8" Point B - 13/16" Center to Center Action Screws: 7 15/16" Comes with Boyds 1/2 Recoil Pad. ATTENTION CUSTOMERS: You will need your factory Rear Action Screw, Rear Action Screw Lug, Mag Box. ATTENTION CUSTOMERS: We will provide the Trigger Guard, Front Action Screw and Wood Screw, and Recoil Lug. Boyds recommends Glass Bedding at the forward Recoil Lug area. Exchange Factory Front Action Screw with Boyds provided Front Action Screw. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

PH SAV 12 TBR BLIND MAG SA CENTER FEED FBC FOREST CAMO SATIN FINISH BOYDS PAD ADJUSTABLE COMB PILLAR BEDDING LOP 13 1/4" ATTENTION CUSTOMERS: ODD SHAPED IMPRESSIONS ON RIGHT SIDE OF STOCK ABOVE TRIGGER GUARD AREA, NOT SCRATCHES OR DENTS Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page. This stock is designed for the Savage Blind Magazine with Center Feed Action and a top bolt release. When you disassemble your action the magazine box will stay inside the stock when the barreled action is removed. If the magazine box stays attached to the action, you may need the Staggered Feed Model or STAGGERED FEED version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

CLA BROWNING A-BOLT LA LH STK RH ACT FBC FOREST CAMO SATIN FINISH BLACK GRIP CAP PILLAR BEDDING Barrel Dimensions: Point A = 1 1/4" and Point B = 13/16"Center to Center of Action Screws: 8"Over All Length of Part: 31/1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS:;Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out;Browning;for more info.All finished stocks have been CNC inlet to Boyds House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

PH B-SERIES LH STK LH ACT FBC FOREST CAMO SATIN FINISH BOYDS PAD LASER PANEL BLACK GRIP CAP ANGLED BLACK TIP CAP LOP 12 3/4" Barrel Dimensions: Where barrel meets receiver/Point A=.8" Point B/9 inches in front of Point A= .675" Center to Center of Action Screws: 3.35" Over All Length of Part: 31.5" This Inlet will work for both long rifle and magnum action. Attention Customers: We provide the washer for the front take down screw and a trigger guard. Attention Customers: It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable and nonreturnabe.

PH SKS YUGO 59/66 MILITARY BARREL CHANNEL MAROON HIGH GLOSS BOYDS PAD WHITE LINE SPACER BLACK GRIP CAP ATTENTION CUSTOMERS: DENTED ON LEFT SIDE OF GRIP Barrel Dimensions: Point A = 27/32" and Point B = 11/16" Center to Center of Action Screws: N/AComes with Boyds' 1/2" Rubber Recoil Pad. We also provide the rear swivel stud. Customer will need all parts from original stock. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This inlet was developed using a Yugo Model 59/66 with a blade style bayonet. It is our understanding that this inlet will work for most, if not all, SKS model manufactures or variations thereof with minor fitting. (e.g. spike bayonets will require fitting and the Albanian SKS is an example of a variation that will not fit.) Due to the varying ages, manufacture, condition and wear of SKS firearms, removal of wood or shimming the lower bearing surface at the rear of the trigger guard (fire control group) may be required to achieve a solid lock-up when the fire control group is installed and latched. We have picked a 'sweet spot' for this elevation that should provide this in most cases, but modification may be needed to get your desired result. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

LH FT KIMBER 84M SA LH STK RH ACT FBC APPLE JACK HIGH GLOSS BOYDS PAD ATTENTION CUSTOMERS: SANDING CIRCLES UNDER FINISH BACKSIDE OF COMB It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions: Point A = 1 3/64" and Point B = 43/64" Center to Center of Action Screws: 6 9/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:You will need the mag box, shell follower and spring, takedown screws, and trigger guard with trigger screw. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final!

HERT TIKKA T1X DBM LH STK FBC SHADY CAMO SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 7/8" and Point B = 3/4" Center to Center of Action Screws: 7" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety is located on the tang and the Bolt Release is on the side of the receiver. ATTENTION CUSTOMERS : Steel lug will be furnished with the stock. Ensure proper installation of the lug during assembly. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

Browning® A-5 12 Ga Fe WALNUT WOOD FILL FINISH It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: N/A Barrel Channel Point B: N/A Magazine Tube Width: N/A Recoil Spring cut out measures 7 9/16" from front receiver Over All Length of Part: 11 1/8" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS: These forends do not come with forward Cap retaining spring. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

FT BERGARA B14 RIDGE SHORT ACTION 1-PIECE FLOOR PLATE BULL BARREL CHANNEL ROYAL JACARANDA HIGH GLOSS LIMBSAVER PAD PILLAR BEDDING LOP 14" Barrel Channel Dimensions : Point A - 1 1/4" Point B - 7/8" Center to Center Action Screws: 6 1/2"ATTENTION CUSTOMERS: You will need the floor plate, mag box liner, and the front and rear action screws from the original stock. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

FIELD DESIGN BROWNING BAR MKII STOCK AND FOREND CLARO XX WALNUT ELITE FINISH PACHMAYR PAD LASER PANEL STOCK It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: N/A" Top Tang Length: N/A" Bottom Tang Width: 9/16" Bottom Tang Length: 7/8" Stock Height at Receiver: 2" Stock Width at Receiver: 1 5/16" Overall Length of Stock:13 1/16" Measurement of Receiver Mounting Bolt: 5 3/4" BUTTPLATE ATTENTION CUSTOMER: Before you order, you must confirm which type of Browning BAR you have. Visit the Browning Web site or contact Browning directly to determine your version. You will need the Reciever Mounting Bolt(Not necessary for Sterling Shape) from the factory stock. We will provide the Butt Pad w/screws & Reciever Mounting Bolt for Sterling Shape. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: 1 17/64" Barrel Channel Point B: 3/4" Receiver Edge to Center of Mounting Screw: 9 7/32" Over All Length of Part: 13" ATTENTION CUSTOMERS:You will need the original swivel stud mounting screw. We will be providing the bushing/spacer where the swivel stud mounts to the gun. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

FIELD DESIGN REM 11 TYPE 1 12GA STOCK WALNUT ELITE FINISH BOYDS PLASTIC BUTTPLATE LASER PANEL TYPE 1 STOCKS WILL GENERALLY HAVE SERIAL NUMBERS BELOW 170,000 It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 5/8" Top Tang Length: 3 5/8" Bottom Tang Width: 5/8" Bottom Tang Length: 2 15/16" Stock Height at Receiver: 1 5/8" Stock Width at Receiver: 1 7/16" Overall Length of Stock: 13 1/2" Come with Boyds' Black Plastic Buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

Spike Camp SAV 220 SLUG GUN DBM LA EXTD FP LH ACT FBC Zombie Hunter Satin Finish Boyds Pad Laser Symbol: Wolf Barrel Dimensions: Point A = 1 1/16" and Point B = 14/16" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS: Longer floor plate for this model is 6 3/16" and is .4 longer than the older version. The gun is chambered for a 20 GAUGE shotgun shell. You will need the trigger guard, floor plate/mag plate, and all take down screws from the original stock. We will installed the swivels. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

Spike Camp WIN 70 SUPER SHORT ACTION BLIND MAGAZINE FACTORY BARREL CHANNEL POST 64 Nutmeg High Gloss Boyds Pad Laser Panel Pillar Bedding Barrel Dimensions: where barrel meets receiver/Point A=1.138" Barrel Dimensions: 9 inches in front of Point A/Point B= .668" Center to Center of Action Screws: 6.35" Attention Customers: Winchester Super Short Magnum-Blind Mag-NO FLOOR PLATE Attention Customers: It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

CLASSIC WEATHERBY MARK V LONG ACTION 1-PC FLOOR PLATE LEFT HAND STOCK RIGHT HAND ACTION FBC Walnut High Gloss Finish Pachmayr Pad Walnut Grip Barrel Dimensions: Point A = 1.140" and Point B = 0.680"Center to Center of Action Screws: 8.105" Over All Length of Part: 32"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.ATTENTION CUSTOMERS:You will need the floorplate and action screws from your original stock. ATTENTION CUSTOMERS: These stocks are designed for rifles with a 6 lug bolt, and are not compatible with rifles with a 9 lug bolt system.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & Nonreturnable.

PH CZ 550 AMERICAN LA FBC CLARO X WALNUT SATIN FINISH PACHMAYR PAD WHITE LINE SPACER BLACK TIP CAP BLACK GRIP CAP ATTENTION CUSTOMERS: MISSING WHITE LINE BETWEEN TIP AND GRIP. 14" LOP It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Barrel Dimensions: Point A = 1 7/64" and Point B = 47/64"Center to Center of Action Screws: 7 53/64"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS:  You will need your takedown screws, floor plate assembly, and mag well. All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

SPIKE CAMP WIN 70 SA 1PC FP FBC POST 64 ROYAL SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 29 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS:This stock will not work for the WSSM caliber rifles. Pre 1984 actions are based on the long action receiver.These stocks are designed for the Short Action 1 piece hinged floor plate with standard factory tapered barrel. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:This stock will not work for the WSSM caliber rifles. Pre 1984 actions are based on the long action receiver.These stocks are designed for the Short Action 1 piece hinged floor plate with standard factory tapered barrel. All Rapid Fire sales are final!

CLA SAV 11 BOLT ACT LH STOCK RH ACT SHORT ACTION, BLIND MAGAZINE BBC NUTMEG SATIN FINISH LIMBSAVER PAD Barrel Dimensions: Point A = 1.310" and Point B = .930"Center to Center of Action Screws: 4.415" Over All Length of Part: 31.50"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need take down screws, and trigger guard & screw from the factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

FT SAV 11 BOLT ACTION SHORT ACTION, BLIND MAGAZINE, BULL BARREL CHANNEL NUTMEG SATIN FINISH KICK-EEZ PAD Barrel Dimensions: Point A = 1.310" and Point B = .930"Center to Center of Action Screws: 4.415" Over All Length of Part: 31.50"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need take down screws, and trigger guard & screw from the factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

SPIKE CAMP REMINGTON 700 SA DBM COYOTE SATIN FINISH BOYDS PAD LASER PANEL PILLAR BEDDING Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4" Center to Center of Action Screws: 6 1/2" Over All Length of Part: 29 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is inlet for the standard factory tapered barrel. These stocks are designed for the Remington 700 receiver with factory supplied detachable box magazine. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

LH FT WEATHERBY MARK V LA 1PC HINGED FP LH STOCK RH ACTION FBC NUTMEG SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1.140" and Point B = 0.680"Center to Center of Action Screws: 8.105" Over All Length of Part: 32"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.ATTENTION CUSTOMERS:You will need the floorplate and action screws from your original stock. ATTENTION CUSTOMERS: These stocks are designed for rifles with a 6 lug bolt, and are not compatible with rifles with a 9 lug bolt system.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

LH HERT WEATHERBY MARK V Long Action 1pc Hinged Floor Plate Left Hand Stock Right Hand Action Factory Barrel Channel ROYAL JACARANDA SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1.140" and Point B = 0.680"Center to Center of Action Screws: 8.105" Over All Length of Part: 32"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.ATTENTION CUSTOMERS:You will need the floorplate and action screws from your original stock. ATTENTION CUSTOMERS: These stocks are designed for rifles with a 6 lug bolt, and are not compatible with rifles with a 9 lug bolt system.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

SPIKE CAMP SAVAGE 111 TROPHY HUNTER BBR DETACHABLE MAG LA LH ACT FBC SKY SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage detachable box magazine rifle with bottom bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock.ATTENTION CUSTOMERS: Attention Customer: If you have an Apex Hunter model it will not be a direct fit in this stock, as it will require modifying the trigger area for clearance due to differences in the trigger mechanism. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE LA PLASTIC MAG WELL from our Accessories page, Part No. A09160 or SAVAGE LA METAL MAG WELL, Part No. A09213. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from the Accessories page, SAVAGE LA PLASTIC MAG WELL, part no. A09160. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

HERT CURTIS CUSTOMS AXIOM SA DBM AI STYLE FBC WALNUT SATIN FINISH BOYDS PAD ATTENTION CUSTOMERS: RUN IN FINISH BY COMB. Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center Action Screws: 6 1/2" Comes with Boyds 1/2" Recoil Pad. ATTENTION CUSTOMERS: You will need your factory floor plate, mag box, front and rear action screws.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

CLA KIMBER 84M SA FBC PEPPER SATIN FINISH BOYDS PAD It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions: Point A = 1 3/64" and Point B = 43/64" Center to Center of Action Screws: 6 9/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:You will need the mag box, shell follower and spring, takedown screws, and trigger guard with trigger screw. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

LH PLAT BROWNING AB2 SSA 2PC HINGED FLOOR PLATE LH STK FBC PEPPER SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1.176" and Point B = .842"Center to Center of Action Screws: 6.66"Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need the floor plate, take down screws, trigger guard and screw from your factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a . All Rapid Fire sales are final! Nonreturnable & nonrefundable.

RIMFIRE HUNTER CZ 452-2E AMERICAN SA CLIP FEED LH ACT FBC PEPPER SATIN FINISH BOYDS PAD ATTENTION CUSTOMERS: SCRATCHES AND DENTS ON BUTTSTOCK, BOTH SIDES. Barrel Dimensions: Point A = .99" and Point B = .712"Center to Center of Action Screws: 3.235"Over All Length of Part: 31.25"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need floor plate, take down screws, trigger plate and clip from the factory stock. ATTENTION CUSTOMERS: Not compatible with ZKM model variations. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

LH FT SAVAGE 112 TBR BLIND MAG STFG LH STK RH ACT FBC Forest Camo Satin Finish Boyds Pad ATTENTION CUSTOMERS: Bubbles in the finish on comb. Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page. This stock is designed for the Savage Model Blind Magazine with Staggered Feed action and a top bolt release. When you disassemble your action the magazine box will be attached to the receiver. If the magazine box stays inside of the stock when the barreled action is removed, you may need the Center Feed Model or CTF version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

HERT REMINGTON 700 SA DBM HAWKINS PRECISION M5 FBC Black Textured Paint Boyds Pad ATTENTION CUSTOMERS: Dented cheek piece Barrel Channel Dimensions: Point A - 1 1/4" Point B - 3/4" Center to Center Action Screws: 6 1/2" Comes with Boyds 1/2" recoil pad. ATTENTION CUSTOMERS: This inlet is machined to accept the Hawkins Precision M5 Detachable Box Magazine Short Action Bottom Metal. You will need to purchase the Hawkins Precision M5 Bottom Metal separately. Inlet is not milled for Hawkins pillars due to end user preference. Refer to Hawkins Precision for specifics of the M5 Detachable Box Magazine. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

SPIKE CAMP SAVAGE 93 LEFT HAND ACTION, BULL BARREL CHANNEL Forest Camo Satin Finish Boyds Pad Barrel Dimensions: Point A = 13/16" and Point B = 13/16" Center to Center of Action Screws: 3 11/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: This stock is designed for the Sav93-E/MKII heavy barrel with inlet trigger guard and floor plate. Action measures 7 3/4" long on the 93E/MKII action. Pre-93E receivers (with a lug at the back of the reciever) can be fit to our 93E/MKII stocks but will require fitting of your receiver and barrel to the stock. Minor gap will be visible on rear of stock with older pre-accutrigger actions. Older receivers are about 4 inches longer and will need to be fit. Variations in action mounting screw pillars exist between models. Do not over tighten. ATTN customers: Side mount rear peep sights will require modifications of the stock for fitment. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page, bottom left-hand corner. Part numbers for 22 LR: 100654 (Blued), 100655 (Nickel). Part numbers for 17hmr/22mag: 100656 (Blued), 100657 (Nickel). Some stocks may also require different action screws which are available through DiProductsInc: PN 13020. Variations in action mounting screw pillars exist between models. Do not over tighten. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

SPIKE CAMP SAVAGE 111 SIDE RELEASE DBM LA FBC COYOTE HIGH GLOSS BOYDS PAD It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Barrel Dimensions: Point A = 1 21/64" and Point B = 23/32"Center to Center of Action Screws: 5 1/16”Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS:  This inlet is for the side release magazine version. You will need your trigger guard with screws and side release button.  All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

HERT BROWNING A-BOLT MICRO SA FBC WALNUT SATIN FINISH BOYDS PAD It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions: Point A = 1 11/64" and Point B = 43/64"Center to Center of Action Screws: 7 13/64"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS: Before you order, you must confirm, by serial number, if your firearm model is an A-Bolt, A-Bolt II (2), or A-Bolt III (3). The roll stampings on all versions only states A-Bolt regardless of model. Also, you will need to confirm if your particular firearm is a Micro version or not. Micro versions are different than the standard models. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect All Rapid Fire sales are final! Nonreturnable & nonrefundable.

AP REM 1100 12 GA STOCK & FOREND XX WALNUT SATIN FINISH PACHMAYR PAD FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: N/A Barrel Channel Point B: N/A Receiver Edge to Center of Mounting Screw/Magazine Tube Width: 1 9/16 " Magazine Tube Shoulder to Shoulder: N/A Over All Length of Part: 11 3/4 All finished parts have been CNC inlet to Boyds' House Action. Variations exist on these forends including that may require minor fitting to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect STOCK It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Top Tang Width: N/ATop Tang Length: N/ABottom Tang Width: 9/16"Bottom Tang Length: 9/16"Stock Height at Receiver: 2"Stock Width at Receiver: 1 7/16"Overall Length of Stock: 13 3/4"Measurement of Receiver Mounting Bolt: 10 1/2"Comes with Pachmayr recoil pad All Rapid Fire sales are final! Nonreturnable & nonrefundable.

FT SAV 110 TACTICAL AICS MAG HEAVY BARREL CHANNEL SHADY CAMO SATIN FINISH BOYDS PAD LASER PANEL ANGLED WALNUT TIP CAP PILLAR BEDDING Barrel Dimensions: Point A = 1 1/16" and Point B = 14/16" Center to Center of Action Screws: 4 7/16" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: You will need to order the Savage Screw Set from the Accessories page(PART #: 100010). This stock is designed for the Savage 110 Tactical model that utilizes an AICS platform and has a heavy barrel. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

PH BROWNING X-BOLT SA LH STK LH ACT FBC PEPPER SATIN FINISH PACHMAYR PAD LOP 13 1/4" Barrel Dimensions: Point A = 1 7/64" and Point B = 45/64" Center to Center of Action Screws: 4 5/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. The Safety is located on the tang and the Bolt Release is on the side of the receiver. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

PH MOSSBERG MVP DBM SA FBC APPLE JACK SATIN FINISH BOYDS PAD ADJUSTABLE COMB Barrel Dimensions: Point A = 1" and Point B = 45/64" Center to Center of Action Screws: 4 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: You will need your magazine liner, trigger guard with screw, takedown bolts, and take down bolt head washer. ATTENTION: Not compatible with LR Tactical with AR-Style Magazine. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

LH CLA BROWNING A-BOLT SHORT ACTION LEFT HAND STOCK RIGHT HAND ACTION FBC WALNUT HIGH GLOSS BOYDS PAD Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4"Center to Center of Action Screws: 7 1/4"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS:Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out;Browning;for more info.All finished stocks have been CNC inlet to Boyds House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

SPIKE CAMP SAVAGE 93E MKII LEFT HAND ACTION BULL BARREL CHANNEL PEPPER SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 13/16" and Point B = 13/16" Center to Center of Action Screws: 3 11/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: This stock is designed for the Sav93-E/MKII heavy barrel with inlet trigger guard and floor plate. Action measures 7 3/4" long on the 93E/MKII action. Pre-93E receivers (with a lug at the back of the reciever) can be fit to our 93E/MKII stocks but will require fitting of your receiver and barrel to the stock. Minor gap will be visible on rear of stock with older pre-accutrigger actions. Older receivers are about 4 inches longer and will need to be fit. Variations in action mounting screw pillars exist between models. Do not over tighten. ATTN customers: Side mount rear peep sights will require modifications of the stock for fitment. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page, bottom left-hand corner. Part numbers for 22 LR: 100654 (Blued), 100655 (Nickel). Part numbers for 17hmr/22mag: 100656 (Blued), 100657 (Nickel). Some stocks may also require different action screws which are available through DiProductsInc: PN 13020. Variations in action mounting screw pillars exist between models. Do not over tighten. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

PV CZ 550 DBM SA BBC Black Textured Paint Limbsaver Pad Laser Panel LOP 14" Barrel Dimensions: Point A = 1 7/64" and Point B = 55/64" Center to Center of Action Screws: 7 13/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & Nonreturnable.

Hert Rem 700 SA Detachable Mag FBC Black Textured Paint Boyds Pad Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4" Center to Center of Action Screws: 6 1/2" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is inlet for the standard factory tapered barrel. These stocks are designed for the Remington 700 receiver with factory supplied detachable box magazine. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable and nonreturnable.

PV CZ 550 DBM SA BBC Nutmeg High Gloss Limbsaver Pad Laser Panel ATTENTION CUSTOMERS: VISIBLE SANDING MARKS THROUGHOUT STOCK, SCUFF ON RIGHT HAND SIDE OF BUTTSTOCK, LITTLE DENT RH SIDE OF FOREND, FINISH FLAW ON BOTTOM OF BUTT, NATURAL WOOD FLAWS BELOW BOLT CUT, AND OPPOSITE SIDE OF FOREND. Barrel Dimensions: Point A = 1 7/64" and Point B = 55/64" Center to Center of Action Screws: 7 13/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

SPIKE CAMP THUMBHOLE, SAVAGE® 93 BOLT ACTION, LEFT HAND ACTION, BULL BARREL CHANNEL SHADY CAMO SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 13/16" and Point B = 13/16" Center to Center of Action Screws: 3 11/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: This stock is designed for the Sav93-E/MKII heavy barrel with inlet trigger guard and floor plate. Action measures 7 3/4" long on the 93E/MKII action. Pre-93E receivers (with a lug at the back of the reciever) can be fit to our 93E/MKII stocks but will require fitting of your receiver and barrel to the stock. Minor gap will be visible on rear of stock with older pre-accutrigger actions. Older receivers are about 4 inches longer and will need to be fit. Variations in action mounting screw pillars exist between models. Do not over tighten. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page, bottom left-hand corner. Part numbers for 22 LR: 100654 (Blued), 100655 (Nickel). Part numbers for 17hmr/22mag: 100656 (Blued), 100657 (Nickel). Some stocks may also require different action screws which are available through DiProductsInc: PN 13020. Variations in action mounting screw pillars exist between models. Do not over tighten. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

CLA SAKO 75-1 HUNTER SA FBC CLARO X WALNUT SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1.042" and Point B = .707"Center to Center of Action Screws: 6.683" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need floor plate, take down screws, and mag box from the factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

AMERICAN PLAINSMAN REMINGTON 870 12GA STOCK Nutmeg ATTENTION CUSTOMERS: 10 1/2" factory stock bolt is required for this buttstock. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Top Tang Width: N/ATop Tang Length: N/ABottom Tang Width: 1/2"Bottom Tang Length: 5/8"Stock Height at Receiver: 1 15/16"Stock Width at Receiver: 1 1/2"Overall Length of Stock: 13 3/4"Measurement of Receiver Mounting Bolt - 10 1/2Comes with Pachmay Decelerator recoil padAll finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.ATTENTION CUSTOMERS: These stocks are designed for the larger frame models. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

AMERICAN PLAINSMAN REMINGTON 870 12GA STOCK Pepper ATTENTION CUSTOMERS: 10 1/2" factory stock bolt is required for this buttstock. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Top Tang Width: N/ATop Tang Length: N/ABottom Tang Width: 1/2"Bottom Tang Length: 5/8"Stock Height at Receiver: 1 15/16"Stock Width at Receiver: 1 1/2"Overall Length of Stock: 13 3/4"Measurement of Receiver Mounting Bolt - 10 1/2"Comes with Pachmay Decelerator recoil padAll finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.ATTENTION CUSTOMERS: These stocks are designed for the larger frame models. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

AMERICAN PLAINSMAN REMINGTON 870 12GA STOCK Walnut It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need to purchase the 8 5/16" mounting bolt for wood stocks from the Accessories page, Part Number: A09168.Top Tang Width: N/ATop Tang Length: N/ABottom Tang Width: 1/2"Bottom Tang Length: 5/8"Stock Height at Receiver: 1 15/16"Stock Width at Receiver: 1 1/2"Overall Length of Stock: 13 3/4"Measurement of Receiver Mounting Bolt - 8 5/16"Comes with Pachmay Decelerator recoil padAll finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.ATTENTION CUSTOMERS: These stocks are designed for the larger frame models. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

FT WIN 70 PRE-64 LA 2PC FP FBC Black Jack Satin Finish Limbsaver Pad Laser Symbol: Wolf Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4" Center to Center of Action Screws: 7 7/16" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS: These stocks are designed for the Winchester model 70 pre 64 long action, with a 2 piece floor plate, factory barrel. You will need your factory Trigger Guard, 2-Piece Hinged Floor Plate, 3 Action Screws, Machine Screw w/escutcheon(Forend Location) & Magazine Box. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

PLAT REM 700 LA 1PC FP LH STOCK RH ACT BBC Walnut Satin Finish Pachmayr Pad Laser Panel Pillar Bedding Barrel Dimensions: Point A = 1.245" and Point B = 0.9"Center to Center of Action Screws: 7.345" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS:You will need the floor plate, mag box, and take down screws from your factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

Savage® 67 (top Rec Safety) Stock WALNUT UNFINISH BOYDS BUTTPLATE These parts are designed to fit the Savage,Stevens,Springfield and Fox models 30,67,77,79,168 and 176 stocks with top receiver safety, please compare your stock and receiver measurements with those we supply.Make sure to confirm demensions with those supplied for this parts. There may be up to five variations of this model.Top Tang width - 9/16ths"Top Tang length - 1 7/16ths"BottomTang width - 5/8ths"BottomTang length - 1 5/16ths"Stock height at receiver -1 5/8ths"Stock width at receiver -1 1/2" Semi-inlet parts have been comletely shaped and 95% machine inlet. Stocks are rough sanded and unless otherwise specified, are shipped with a BOYDS' butt plate.(SEMI-INLET) stocks do require some knowledge of firearms and woodworking for installation. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

PH BROWNING A-BOLT SHORT ACT FBC NUTMEG HIGH GLOSS BOYDS PAD ANGLED BLACK TIP BLACK GRIP CAP LASER INITIALS: LEA FONT #2 Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4"Center to Center of Action Screws: 7 1/4"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info.All finished stocks have been CNC inlet to Boyds House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

HERITAGE MOSSBERG 100 ATR SA FBC XX MAPLE HIGH GLOSS WHITE LINE SPACER BOYDS PAD BLACK GRIP CAP LASER PANEL ATTENTION CUSTOMERS: Visible sanding marks throughout stock. Slight dent on comb. Barrel Dimensions: Point A = 1 3/8" and Point B = 13/16" Center to Center of Action Screws: 4 9/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: If you are converting from a plastic stock, you will need to purchase a trigger guard from our Accessories page: ITEM # A09157, and an action screw from Mossberg directly, ITEM # 101532. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

SPIKE CAMP WIN 70 SA 2PC FP FBC POST 64 Royal Jacaranda Satin Finish Boyds Pad Laser Panel Pillar Bedding Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 29 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock will not work for the WSSM Caliber Rifles. Pre-1984 actions are based on the Long Action receiver. These stocks are designed for the Winchester Model 70 Short Action 2-Piece hinged floor plate model with a standard factory tapered barrel. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

LH PH SAV A22 MAGNUM SEMI-AUTO DBM LH STK RH ACT FBC WALNUT SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 0.92" and Point B = 0.69"Center to Center of Action Screws: 7.444" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable and nonrefundable.

SPIKE CAMP THUMBHOLE, SAVAGE 111 TBR, BLIND MAGAZINE, LONG ACTION, CENTER FIRE, LH ACTION, FACTORY BARREL CHANNEL Coyote Satin Finish Boyds Pad Laser Panel Pillar Bedding Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately in our gun parts section on the LEFT hand side of our webpage. This stock is designed for the Savage Blind Magazine with Center Feed Action and a top bolt release. When you disassemble your action the magazine box will stay inside of the stock when the barreled action is removed. If the magazine box stays attached to the action you may need the Staggered Feed Model or STAGGERED FEED version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable and nonreturnable.

CLA SAV 110 TBR 1-PC FP BBC Nutmeg High Gloss Boyds Pad Black Grip Cap Pillar Bedding LOP 12 3/4" Barrel Dimensions: Point A = 1 1/16" and Point B = 15/16" Center to Center of Action Screws: 5 1/16" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on the Accessories Page.ATTENTION CUSTOMERS: You will need your factory Floor Plate, Front Action Screw, Rear Action Screw, Wood Screw, Trigger Guard, Rear Action Screw spacer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.All Rapid Fire sales are final! Nonrefundable & nonreturnable.

SPIKE CAMP BROWING T-BOLT RIMFIRE 22LR LH ACT Shady Camo Satin Finish Boyds Pad Barrel Channel Dimensions : Point A - 15/16" Point B - 15/16" Center to Center Action Screws: 2 1/2" It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. This stock is inletted for the 22LR caliber. ATTENTION CUSTOMERS: You will need your floor plate, mag box, and the 2 action screws from your original stock. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

SPIKE CAMP SAV 110 TBR LONG ACTION DBM FBC Sky Satin Finish Boyds Pad Laser Initials: CJH Font #3 Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage detachable box magazine rifle with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Long Action Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE LA PLASTIC MAG WELL from our Accessories page, Part No. A09160 or SAVAGE LA METAL MAG WELL, Part No. A09213.. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

FT WEATHERBY MARK V VARMINTMASTER SA 1PC FP FBC Pepper Satin Finish Limbsaver Pad ATTENTION CUSTOMERS: rough finish top of comb lite scratch by pad Barrel Dimensions: Point A = 1.085" and Point B = .715"Center to Center of Action Screws: 6.867" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need the floor plate, take down screws and mag well from your factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable and nonreturnable.

PLAT BROWNING A-BOLT SHORT ACTION, LH STOCK, RH ACTION, FACTORY BARREL CHANNEL Forest Camo Satin Finish Limbsaver Pad LOP 13 1/4" Barrel Dimensions: Point A = 1 3/16" and Point B = 21/32"Center to Center of Action Screws: 7 1/4"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil PadIt is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: This stock is not designed for Micro Medallion Models. Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II, or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO Versions are different than standard models. Call Browning Customer Service for more information.The WSSM barreled actions do not fit short action stocks.All semi-inlet stocks require final fitting to your action and final sanding and finish of exterior of stock. Semi-inlet stocks do require some knowledge of firearms and woodworking for installation.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

PLAT REM 783 LA DBM FBC Claro XX Walnut High Gloss Boyds Pad Laser Panel Walnut Grip Cap Angled Walnut Tip White Line Spacer Pillar Bedding Barrel Dimensions: Point A = 1 5/64" and Point B = 3/4" Center to Center of Action Screws: 7 31/32" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

HERT BROWNING A-BOLT SA FBC SHADY CAMO SATIN FINISH KICK-EEZ PAD PILLAR BEDDING LOP 13 1/4" Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4" Center to Center of Action Screws: 7 1/4" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Boyds' has designed the Browning A-Bolt stocks so you do not have to use the rear metal shim that is supplied by Browning for some models. These parts are manufactured using standard Browning short - action receivers. They are not intended for Micro-medallion series or any WSSM action. Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II, or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO Versions are different than standard models. Call Browning Customer Service for more information. All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

LH CLASSIC TC VENTURE SHORT ACTION LEFT HAND STOCK RIGHT HAND ACTION FBC MAROON SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1 3/16" and Point B = 45/64" Center to Center of Action Screws: 6 29/32" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: You will need your takedown screws and magazine from your original stock.Short Action calibers- 22-250 Rem, 308 Win, 7mm-08 Rem. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

STERLING BROWNING® BAR TYPE 2 STK NUTMEG SATIN FINISH BOYDS 1" VENTED PAD ATTENTION CUSTOMERS: BLEMISHES IN FINISH ON EDGE OF THUMBHOLE WHERE IT CONNECTS TO THE COMB, RUN IN THUMBHOLE FINISH, FEW DENTS TOO. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Top Tang Width: N/A"Top Tang Length: N/A"Bottom Tang Width: 5/8"Bottom Tang Length: 3/4"Stock Height at Receiver: 2"Stock Width at Receiver: 1 3/8"Overall Length of Stock:13 1/16"Measurement of Receiver Mounting Bolt: 5 3/4"BUTTPLATEAll finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.