Gunstocks

AT-ONE CZ® 452 2E AMERICAN BOLT, SHORT ACTION, CLIP, FACTORY BARREL CHANNEL, ZZ Barrel Dimensions: Point A = .99" and Point B = .712"Center to Center of Action Screws: 3.235"Over All Length of Part: 31.25"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need floor plate, take down screws, trigger plate and clip from the factory stock. ATTENTION CUSTOMERS: Not compatible with ZKM model variations. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, BROWNING A-BOLT, SHORT ACTION, LH STOCK, RH ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4"Center to Center of Action Screws: 7 1/4"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS:Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out;Browning;for more info.All finished stocks have been CNC inlet to Boyds House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

C.I.L. 710 20 GA SPLINTER, FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: N/A" Barrel Channel Point B: N/A" Receiver Edge to Center of Mounting Screw/Magazine Tube Width: N/A" Center to Center of Mounting Screws/Magazine Tube Shoulder to Shoulder: N/A" Over All Length of Part: 7 1/2" Over All width at receiver: 1 1/2" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.ATTENTION CUSTOMERS:Final fitting of spring clip assembly and drilling for mounting screws maybe required due to the many variations of mounting hardware used on this model.

BROWNING X-BOLT, AT-ONE, LONG ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 7/64" and Point B = 45/64" Center to Center of Action Screws: 5" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. The Safety is located on the tang and the Bolt Release is on the side of the receiver. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CHICAGO LONG RANGE DBL SEMI-BEAVERTAIL FOREND 12GA, ZZ It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: N/A" Barrel Channel Point B: N/A" Receiver Edge to Center of Mounting Screw/Magazine Tube Width: N/A" Center to Center of Mounting Screws/Magazine Tube Shoulder to Shoulder: N/A" Over All Length of Part: 9" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:This forend is designed for mounting hardware measuring 4 13/16" long with interior mounting screws. You will need to predrill for screws.

RH CZ® 452 .22 MAG, BULL BARREL CHANNEL, ZZ Barrel Dimensions: Point A = 1 1/16" and Point B = 15/16" Center to Center of Action Screws: 5 13/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: The 452 Magnum stocks are designed for the rear action mounting screw models using metal trigger guard and floor plate. Please compare the inletting photos with your stock to confirm the proper model is ordered. If your model does not come with rear receiver mounting screw, please review 452 .22LR for possible compatibility. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

FOX® B-C, 16 GA SPLINTER FOREND, ZZ It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: N/A" Barrel Channel Point B: N/A" Receiver Edge to Center of Mounting Screw/Magazine Tube Width: N/A" Center to Center of Mounting Screws/Magazine Tube Shoulder to Shoulder: N/A" Over All Length of Part: 7 1/2" Over All width at receiver: 1 1/2" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:Final fitting of spring clip assembly and drilling for mounting screws maybe required due to the many variations of mounting hardware used on this model.

CLASSIC, CZ 557 CARBINE, ONE PIECE FLOOR PLATE, LONG ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 7/32" and Point B = 47/64" Center to Center of Action Screws: 7 1/2" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

H&R® 480, 580, ROUND TANG, 12 GA STOCK, ZZ PLEASE CONFIRM MEASUREMENTS PRIOR TO ORDERING. Top Tang Width - 1/2" Top Tang Length - 1 7/16" Bottom Tang Width - 1/2 " Bottom Tang Length - 1 1/2 " Stock height at receiver -1 21/32" Stock width at receiver - 1 1/2" Measurement of Receiver Mounting Bolt: 10 1/2" Comes with plastic buttplate ATTENTION CUSTOMERS: This stock is compatible with most standard frame round tang receivers. Due to the many variations of this model, minor fitting may be needed.

CENTRAL ARMS DBL DRAWBOLT 12GA STOCK It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 5/8" Top Tang Length: 2 5/8" Bottom Tang Width: 5/8" Bottom Tang Length: 2 5/8" Stock Height at Receiver: 1 3/4" Stock Width at Receiver: 1 9/16" BUTTPLATE All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS: Please see Stevens 311 series stocks for possible crossover parts if your tang dimensions are not matching the supplied dimensions above.

ESSEX SINGLE ROUND TANG 16 GA STOCK, ZZ PLEASE CONFIRM MEASUREMENTS PRIOR TO ORDERING. Top Tang Width - 1/2" Top Tang Length - 1 7/16" Bottom Tang Width - 1/2 " Bottom Tang Length - 1 1/2 " Stock height at receiver -1 21/32" Stock width at receiver - 1 1/2" Measurement of Receiver Mounting Bolt: 10 1/2" Comes with plastic buttplate ATTENTION CUSTOMERS: This stock is compatible with most standard frame round tang receivers. Due to the many variations of this model, minor fitting may be needed.

GAMBLE SKOGMO 130, 12 GA, RIBBED FOREND, ZZ It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: N/A Barrel Channel Point B: N/A Magazine Tube Width: 1 1/8 Magazine Tube Shoulder to Shoulder: 4 1/2 Over All Length of Part: 6 3/4 All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

H&R® LIGHTWEIGHT SINGLE, ROUND TANG, 20 GA STOCK, ZZ PLEASE CONFIRM MEASUREMENTS PRIOR TO ORDERING. Top Tang Width - 1/2" Top Tang Length - 1 7/16" Bottom Tang Width - 1/2 " Bottom Tang Length - 1 1/2 " Stock height at receiver -1 21/32" Stock width at receiver - 1 1/2" Measurement of Receiver Mounting Bolt: 10 1/2" Comes with plastic buttplate ATTENTION CUSTOMERS: This stock is compatible with most standard frame round tang receivers. Due to the many variations of this model, minor fitting may be needed.

EASTERN ARMS, DOUBLE DRAWBOLT, 16 GA ,BEAVERTAIL, FOREND, ZZ It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: N/A" Barrel Channel Point B: N/A" Receiver Edge to Center of Mounting Screw/Magazine Tube Width: N/A" Center to Center of Mounting Screws/Magazine Tube Shoulder to Shoulder: N/A" Over All Length of Part: 9" Over All width at receiver: 1 7/8" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:Final fitting of spring clip assembly and drilling for mounting screws maybe required due to the many variations of mounting hardware used on this model.

BAR CZ® 452 2E AMERICAN BOLT, SHORT ACTION, CLIP, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = .99" and Point B = .712"Center to Center of Action Screws: 3.235"Over All Length of Part: 27"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need floor plate, take down screws, trigger plate and clip from the factory stock. ATTENTION CUSTOMERS: Not compatible with ZKM model variations.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

FOX® MODEL BST, TYPE 1, 16GA STOCK, ZZ It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 5/8" Top Tang Length: 3 1/8" Bottom Tang Width: 5/8" Bottom Tang Length: 3 7/8" Stock Height at Receiver: 1 7/8" Stock Width at Receiver: 1 5/8" Boyds' Black Plastic Buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, BROWNING® A-BOLT, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4"Center to Center of Action Screws: 7 1/4"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info.All finished stocks have been CNC inlet to Boyds House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

C.I.L. 710 20 GA SEMI BEAVERTAIL FOREND ZZ It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: N/A" Barrel Channel Point B: N/A" Receiver Edge to Center of Mounting Screw/Magazine Tube Width: N/A" Center to Center of Mounting Screws/Magazine Tube Shoulder to Shoulder: N/A" Over All Length of Part: 9" Over All width at receiver: 1 3/4" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:Final fitting of spring clip assembly and drilling for mounting screws maybe required due to the many variations of mounting hardware used on this model.

HERITAGE, BROWNING X BOLT, LH STOCK, RH ACTION, LONG ACTION, DETACHABLE BOX MAGAZINE, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 7/64" and Point B = 45/64" Center to Center of Action Screws: 5" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. The Safety is located on the tang and the Bolt Release is on the side of the receiver. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CHICAGO LONG RANGE DBL BEAVERTAIL FOREND 12GA, ZZ It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: N/A" Barrel Channel Point B: N/A" Magazine Tube Width: N/A" Center to Center of Mounting Screws: N/A" Over All Length of Part: 9 " Over All Width of part: 2" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:This forend is designed for mounting hardware measuring 4 13/16" long and 5/8ths wide with interior mounting screws. Forends are not pre drilled for mounting screws.