Gunstocks

QUEST MARLIN® 795, CLIP FEED, FACTORY BARREL CHANNEL, STOCK, ZZ, FINISHED Barrel Dimensions: Point A = 13/16" and Point B = 13/16" Center to Center of Action Screws: N/A Width of Trigger Guard: 27/32" Length of Trigger Guard: 6 13/16" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to fit the Marlin Model 795 Clip Feed Rifle with the U-shaped trigger guard. Early models are longer and are shaped differently. DIP Products sells new U-shaped trigger guards if desired. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST REMINGTON 541-S, CLIP FEED, SHORT ACTION, FACTORY BARREL CHANNEL It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Barrel Dimensions: Point A = 51/64" and Point B = 47/64"Over All Length of Part: 29 1/4""Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS:  This is a single takedown screw model, barrel will not be free floated. You will need the floor plate screw, takedown screw, and trigger guard with screw. All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST, BROWNING A-BOLT 2, SHORT ACTION, FACTORY BARREL CHANNEL It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions:Where Barrel meets the receiver/ Point A = 1.175" Barrel Dimensions: 9 inches in front of Point A/ Point B = .680 Center to Center of Action Screws: 7.2" Over All Length of Part: 29 1/4"Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and trigger guard.Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info. Attention Customer WSM calibers may require widening of the magazine box opening. Width of mag box opening Front: 15/16" Rear: 1 1/8".All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Quest Thumbhole, Remington 700 XCR ADL, Long Action, Factory Barrel Channel Barrel Dimensions: Point A = 1 1/4" and Point B = 25/32" Center to Center of Action Screws: 7 3/8" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Inlett for standard factory tapered barrel channel. This stock is designed for the Remington 700 Right Hand Long Action with blind magazine, loads and unloads through top of action. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST, MARLIN® 25 Barrel Dimensions: Point A = 0.745" and Point B = 0.745"Center to Center of Action Screws: n/aOver All Length of Part: 29 1/4"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need the Floorplate & Screw and take down screw from your factory stock.  We will provide trigger guard & screws. Barrel does not float.ATTENTION CUSTOMERS: Will not work with the 25MN, 25M, or 25N model variation. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.  Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST, REMINGTON MOHAWK-600, SHORT ACTION, FACTORY BARREL CHANNEL It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions: Point A = 1 17/64" and Point B = 49/64"Center to Center of Action Screws: 5 39/64"Over All Length of Part: 29 1/4"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS: You will need the takedown screws and floorplate from the original stock. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

BROWNING A-BOLT 2, QUEST , LONG ACTION, FACTORY BARREL CHANNEL It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions: Point A = 1 11/64" and Point B = 49/64" Center to Center of Action Screws: 7 59/64" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and trigger guard.Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info. All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST THUMBHOLE, REMINGTON 700 XCR ADL, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4"Center to Center of Action Screws: 6 1/2"Over All Length of Part: 29 1/4"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: This stock is inlett for standard factory tapered barrel channel and is designed for the Remington 700 right hand short action with blind magazine, loads and unloads through top of action.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Quest, Musketeer Mauser, Large Ring, #1 Barrel Channe, Finished Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST, JC HIGGINS MAUSER 51, #1 BARREL CHANNEL, ZZ, FINISHED Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST, REMINGTON 783, LONG ACTION, DETACHABLE BOX MAGAZINE, BULL BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 5/64" and Point B = 31/32" Center to Center of Action Screws: 7 31/32" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

BROWNING A-BOLT MICRO, QUEST, SHORT ACTION, FACTORY BARREL CHANNEL It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions: Point A = 1 11/64" and Point B = 43/64"Center to Center of Action Screws: 7 13/64"Over All Length of Part: 29 1/4"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS: Before you order, you must confirm, by serial number, if your firearm model is an A-Bolt, A-Bolt II (2), or A-Bolt III (3). The roll stampings on all versions only states A-Bolt , regardless of model. Also, you will need to confirm if your particular firearm is a Micro version or not. Micro versions are different than the standard models. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST THUMBHOLE REMINGTON® 700 CDL LA DBM HAWKINS PRECISION M5 BOTTOM METAL FACTORY BARREL CHANNEL Barrel Channel Dimensions: Point A - 1 1/4" Point B - 3/4" Center to Center Action Screws: 7 3/8" Comes with Boyds 1/2" recoil pad. ATTENTION CUSTOMERS: This inlet is machined to accept the Hawkins Precision M5 Detachable Box Magazine Long Action Bottom Metal. You will need to purchase the Hawkins Precision M5 Bottom Metal separately. Inlet is not milled for Hawkins pillars due to end user preference. Refer to Hawkins Precision for specifics of the M5 Detachable Box Magazine. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST, Mossberg® Patriot Bolt, Short Action, Detachable Box Magazine, Factory Barrel Channel Barrel Dimensions: Point A = 1.175" and Point B = .735"Center to Center of Action Screws: 4.715" Over All Length of Part: 29 1/4"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need the mag insert, mag box and take down screws from your factory stock. We will provide a metal trigger guard, rear action screw and wood screw.ATTENTION CUSTOMERS: Mossberg Patriot SA AI Mag Assembly kits are available on the Accessories page, Part# A09164. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST, JC HIGGINS MODEL 50, LONG ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/8" and Point B = 23/32"Center to Center of Action Screws: 7 53/64" Over All Length of Part: 29 1/4"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST, REMINGTON 783, SHORT ACTION , DETACHABLE BOX MAGAZINE, BULL BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 5/64" and Point B = 31/32" Center to Center of Action Screws: 7 13/32" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

BROWNING T-BOLT, QUEST, SHORT ACTION, CLIP FEED, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 55/64" and Point B = 23/32" Center to Center of Action Screws: 5 47/64" Over All Length of Part: 29.25" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS: This inletting will fit all T-Bolt models manufactured from 1965-1974. The design of this gun will not allow a free floated barrel. Boyds' inlets will have a barrel pad at the front of the barrel channel. You will need the takedown screw, trigger, and floor plate with screw clip. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST THUMBHOLE REMINGTON® 700 CDL SA DBM HAWKINS PRECISION M5 BOTTOM METAL FACTORY BARREL CHANNEL Barrel Channel Dimensions: Point A - 1 1/4" Point B - 3/4" Center to Center Action Screws: 6 1/2" Comes with Boyds 1/2" recoil pad. ATTENTION CUSTOMERS: This inlet is machined to accept the Hawkins Precision M5 Detachable Box Magazine Long Action Bottom Metal. You will need to purchase the Hawkins Precision M5 Bottom Metal separately. Inlet is not milled for Hawkins pillars due to end user preference. Refer to Hawkins Precision for specifics of the M5 Detachable Box Magazine. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST Mossberg® Patriot Bolt, Long Action, Detachable Box Magazine, Factory Barrel Channel Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 5/16" Over All Length of Part: 29.25" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : You will need the Mag Insert, Mag Box, Take Down Screws from your factory stock. We will provide a Metal Trigger Guard, Rear Action Screw, and Wood Screw. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect .