Gunstocks

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions: Point A = 7/8” and Point B = 3/4"Over All Length of Part: 29 1/4"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS: This stock will not allow a free floated barrel.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST THUMBHOLE, SAVAGE 14 TBR, BLIND MAGAZINE, SHORT ACTION, CENTER FEED, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page. This stock is designed for the Savage Blind Magazine with Center Feed Action and a top bolt release. When you disassemble your action the magazine box will stay inside the stock when the barreled action is removed. If the magazine box stays attached to the action, you may need the Staggered Feed Model or STAGGERED FEED version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST, RUGER AMERICAN RANCH LONG ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 37/64" Over All Length of Part: 29.25" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks recommends bedding the front and rear lugs.Long Action Calibers: 270 Win, 30-06 Spfld.ATTENTION CUSTOMERS : Does not work with AI or AR Mags. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST SAV 220 SLUG GUN DBM LA EXTD FP RH ACT FBC ZZ Barrel Dimensions: Point A = 1 1/16" and Point B = 14/16" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS: Longer floor plate for this model is 6 3/16" and is .4 longer than the older version. The gun is chambered for a 20 GAUGE shotgun shell. You will need the trigger guard, floor plate/mag plate, and all take down screws from the original stock.This stock is designed for the right hand bolt action only. We will installed the swivels. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST THUMBHOLE, SAVAGE 14 BOTTOM BOLT RELEASE, AT-ONE, DETACHABLE MAGAZINE, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with bottom bolt release (located on the front of the trigger guard). The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock.ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212.. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from the Accessories page, SAVAGE SA PLASTIC MAG WELL, part no. A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212.. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions: Point A = 3/4" and Point B = 45/64"Over All Length of Part: 29 1/4"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS: This stock will not allow a free floated barrel.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 5/16" and Point B = 1" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 29.25" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. MUST READ: If you have a XP model with a synthetic stock, you will need to purchase the bottom metal component system through Savage or any aftermarket component supplier. Due to the many variations of trigger guards that have been used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST, RUGER 77/22 MAG, FACTORY BARREL CHANNEL, LAMINATED STOCK Barrel Dimensions: Point A = 15/16" and Point B = 3/4" Center to Center of Action Screws: 7 1/2" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: These stocks are designed for the Ruger 77 Bolt Action 22 Long Rifle. Early plastic stocks will require additional mounting hardware to use our stocks. Please contact Ruger or Brownells (800) 741-0015 for the metal trigger guard and clip assembly. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 11/32" and Point B = 55/64" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS : This is for the older style floor plate that measures 5.7875. The gun is chambered for a 20 GAUGE shotgun shell. You will need the trigger guard, floor plate/mag plate, and all take down screws from the original stock. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST, SAVAGE 11, BOTTOM BOLT RELEASE SHORT ACTION DETACHABLE BOX MAGAZINE BULL BARREL CHANNEL Barrel Dimensions: Point A = 1 1/8" Point B = 1 1/16" Center to Center Action Screws: 4 7/16" Overall Length of Part: 29 1/4" Comes with Boyds 1/2" Recoil Pad. ATTENTION CUSTOMERS: You will need your factory Floor Plate, Action Screws and Detachable Box Mag. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with bottom bolt release (located on the front of the trigger guard). The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212.. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from the accessories page SAVAGE SA PLASTIC MAG WELL Item #: A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST, SAVAGE 11 TBR, DETACHABLE MAGAZINE, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. MUST READ: If you have a XP model with a synthetic stock, you will need to purchase the bottom metal component system through Savage or any aftermarket component supplier. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 1/4" and Point B = 13/16" Center to Center of Action Screws: 7 13/16" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Springfield Model A03, Remington and Smith Corona also made these rifles. The easiest way to tell between the 1903 and 1903 A3 Rifles is to note where the rear sight is located. The 1903 A3 Rifle has a rear sight mounted on the back of the action by the bolt handle and 1903 Rifle has a rear sight mounted in front of the action. The area on the LEFT hand side of the stock is relief for the magazine cut-off on the original rifles. These are Sporter stocks, they are not cut for barrel bands and are not intended to be used with handguard. These stocks do not come with a bolt cut. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST RUGER 77/44, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1" and Point B = 47/64" Center to Center of Action Screws: 8 5/32" Bottom Magazine Opening Length: 2 21/32" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS: You will need your takedown screws from your original stock. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 1/32" and Point B = 55/64" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS: This is for the older style floor plate that measures 5.7875. The gun is chambered for a 20 GAUGE shotgun shell. You will need the trigger guard, floor plate/mag plate, and all take down screws from the original stock.This stock is designed for the right hand bolt action only. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SAVAGE 11, QUEST, BOTTOM BOLT RELEASE, DETACHABLE MAGAZINE, SHORT ACTION, LH ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with bottom bolt release (located on the front of the trigger guard). The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock.ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212.. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from Savage or Brownells. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST, SAVAGE 11 TBR, DETACHABLE MAGAZINE, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 29 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. MUST READ: If you have a XP model with a synthetic stock, you will need to purchase the bottom metal component system through Savage or any aftermarket component supplier. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 13/16" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: The easiest way to tell between the 1903 and 1903 A3 Rifles is to note where the rear sight is located. The 1903 A3 Rifle has a rear sight mounted on the back of the action by the bolt handle and 1903 Rifle has a rear sight mounted in front of the action. The area on the LEFT hand side of the stock is relief for the magazine cut-off on the original rifles. These are Sporter stocks, they are not cut for barrel bands and are not intended to be used with handguard. These stocks do not come with a bolt cut. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST RUGER ACF PREDATOR, SHORT ACTION, AR MAG, RIGHT HAND ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/64" and Point B = 3/4" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 29.25"Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear taked down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks recommends bedding the front and rear lugs.. ATTENTION: A relief cut to allow magazine release button clearance has been added. ATTENTION CUSTOMERS : You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimmensional differences they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. ATTENTION: The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with the Ruger Mini 30 Magazines due to the steel mag liner. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 45/64" and Point B = 45/64" Center to Center of Action Screws: 2 45/64" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS: We will provide the trigger guard with two screws. You will need the take down screws and magazine plate from the original stock. ATTENTION CUSTOMERS: If the floor plate from your factory stock is not removeable, you will need the purchase a new floorplate from DIProducts(Sav-13069). Due to variations in floorplates it may require removal of material for a flush fit. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SAVAGE 11, QUEST, BOTTOM BOLT RELEASE, DETACHABLE MAGAZINE, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with bottom bolt release (located on the front of the trigger guard). The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock.ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212.. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212.. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.