Gunstocks

QUEST, MOSIN NAGANT M-38, MILITARY BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 1/4" and Point B = 25/32" Center to Center of Action Screws: 7 3/8" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is inlet to accept the Mosin Nagant 91/30 Barreled action. Alternate models will work but minor fitting may be needed. These are Sporter stocks, they are not cut for barrel bands and are not intended to be used with the handguard. Our stocks are designed for the straight bolt. With fitting experience, they can be inlet for any bolt. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST, HOWA 1500, SHORT ACTION,FACTORY BARREL CHANNEL, ZZ Barrel Dimensions: Point A = 1 1/4" and Point B = 13/16" Center to Center of Action Screws: 7 1/4" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST THUMBHOLE, REMINGTON® 700 SPS, LONG ACTION, FACTORY BARREL CHANNEL, LH ACTION, FINISHED Barrel Dimensions: Point A = 1 1/4" and Point B = 25/32" Center to Center of Action Screws: 7 3/8" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Inlett for standard factory tapered barrel channel. This stock is designed for the Remington 700 LEFT Hand Long Action with hinged floor plate. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST, MAUSER VZ-24, #1 BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST THUMBHOLE, REMINGTON 700 CDL ADL, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4"Center to Center of Action Screws: 6 1/2"Over All Length of Part: 29 1/4"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: This stock is inlett for standard factory tapered barrel channel and is designed for the Remington 700 right hand short action with blind magazine, loads and unloads through top of action.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST, MOSIN NAGANT M-44, MILITARY BARREL CHANNEL,W/ TIMNEY TRIGGER INLET Barrel Dimensions: Point A = 1 1/4" and Point B = 25/32" Center to Center of Action Screws: 7 3/8" Over All Length of Part: 29.25" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock has been inletted to accommodate the Timney trigger with the side safety. This stock is inlet to accept the Mosin Nagant 91/30 Barreled action. Alternate models will work but minor fitting may be needed. These are Sporter stocks, they are not cut for barrel bands and are not intended to be used with the handguard. Our stocks are designed for the straight bolt. With fitting experience, they can be inlet for any bolt. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST, HOWA 1500, LONG ACTION, FACTORY BARREL CHANNEL, ZZ, FINISHED Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4" Center to Center of Action Screws: 7 3/4" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST, BRNO MAUSER LR, #1 BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST THUMBHOLE, REMINGTON 700 SPS ADL, SHORT ACTION ,BULL BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 9/32" and Point B = 31/32" Center to Center of Action Screws: 6 1/2" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is inlett for a factory varmint contour barrel channel and is designed for the Remington 700 right hand short action with blind magazine, loads and unloads through top of action. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 2/16" and Point B = 11/16" Center to Center of Action Screws: 7 13/16" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Butt Pad It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: These stocks have been inletted using Boyds' Remington 798 Action. Numerous models were manufactured based on this action design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST, MOSIN NAGANT, M-44, MILITARY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/4" and Point B = 25/32" Center to Center of Action Screws: 7 3/8" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is inlet to accept the Mosin Nagant 91/30 Barreled action. Alternate models will work but minor fitting may be needed. These are Sporter stocks, they are not cut for barrel bands and are not intended to be used with the handguard. Our stocks are designed for the straight bolt. With fitting experience, they can be inlet for any bolt. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST HERTERS MAUSER LR, #1 BARREL CHANNEL, ZZ, FINISHED Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST, BRAZILIAN MAUSER 1908, #1 BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST THUMBHOLE, REMINGTON 700 SPS, SHORT ACTION, FACTORY BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4" Center to Center of Action Screws: 6 1/2" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Inlett for standard factory tapered barrel channel. This stock is designed for the Remington 700 Right Hand Short Action with hinged floor plate. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST, REMINGTON® 788, SHORT RECEIVER, FACTORY BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 13/64" and Point B = 13/16" Center to Center of Action Screws: 6 3/4" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Remington 788 Short Action.Short Action Calibers- 222 Rem, 223 Rem,22-250 Rem,30-30 Win. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST, MOSIN NAGANT, MILITARY BARREL CHANNEL,W/ TIMNEY TRIGGER INLET Barrel Dimensions: Point A = 1 1/4" and Point B = 25/32" Center to Center of Action Screws: 7 3/8" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock has been inletted to accommodate the Timney trigger with the side safety. This stock is inlet to accept the Mosin Nagant 91/30 Barreled action. Alternate models will work but minor fitting may be needed. These are Sporter stocks, they are not cut for barrel bands and are not intended to be used with the handguard. Our stocks are designed for the straight bolt. With fitting experience, they can be inlet for any bolt. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST H&R 750 PIONEER SINGLE SHOT, FACTORY BARREL CHANNEL, ZZ Barrel Dimensions: Point A = 47/64" and Point B = 47/64" Rear of Receiver to Takedown Bolt: 5 45/64" Over All Length of Part: 29.25" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS: You will need your takedown bolt. We will provide the trigger guard. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

ARGENTINE MAUSER 1909, QUEST, #1 BC Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP REMINGTON 700 SA DBM COYOTE SATIN FINISH BOYDS PAD LASER PANEL PILLAR BEDDING Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4" Center to Center of Action Screws: 6 1/2" Over All Length of Part: 29 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is inlet for the standard factory tapered barrel. These stocks are designed for the Remington 700 receiver with factory supplied detachable box magazine. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

LH FT WEATHERBY MARK V LA 1PC HINGED FP LH STOCK RH ACTION FBC NUTMEG SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1.140" and Point B = 0.680"Center to Center of Action Screws: 8.105" Over All Length of Part: 32"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.ATTENTION CUSTOMERS:You will need the floorplate and action screws from your original stock. ATTENTION CUSTOMERS: These stocks are designed for rifles with a 6 lug bolt, and are not compatible with rifles with a 9 lug bolt system.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

LH HERT WEATHERBY MARK V Long Action 1pc Hinged Floor Plate Left Hand Stock Right Hand Action Factory Barrel Channel ROYAL JACARANDA SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1.140" and Point B = 0.680"Center to Center of Action Screws: 8.105" Over All Length of Part: 32"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.ATTENTION CUSTOMERS:You will need the floorplate and action screws from your original stock. ATTENTION CUSTOMERS: These stocks are designed for rifles with a 6 lug bolt, and are not compatible with rifles with a 9 lug bolt system.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

SPIKE CAMP SAVAGE 111 TROPHY HUNTER BBR DETACHABLE MAG LA LH ACT FBC SKY SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage detachable box magazine rifle with bottom bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock.ATTENTION CUSTOMERS: Attention Customer: If you have an Apex Hunter model it will not be a direct fit in this stock, as it will require modifying the trigger area for clearance due to differences in the trigger mechanism. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE LA PLASTIC MAG WELL from our Accessories page, Part No. A09160 or SAVAGE LA METAL MAG WELL, Part No. A09213. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from the Accessories page, SAVAGE LA PLASTIC MAG WELL, part no. A09160. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

HERT CURTIS CUSTOMS AXIOM SA DBM AI STYLE FBC WALNUT SATIN FINISH BOYDS PAD ATTENTION CUSTOMERS: RUN IN FINISH BY COMB. Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center Action Screws: 6 1/2" Comes with Boyds 1/2" Recoil Pad. ATTENTION CUSTOMERS: You will need your factory floor plate, mag box, front and rear action screws.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

CLA KIMBER 84M SA FBC PEPPER SATIN FINISH BOYDS PAD It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions: Point A = 1 3/64" and Point B = 43/64" Center to Center of Action Screws: 6 9/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:You will need the mag box, shell follower and spring, takedown screws, and trigger guard with trigger screw. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

RIMFIRE THUMBHOLE MAGNUM RESEARCH MLR-1722M .920 SKY SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 59/64" and Point B = 59/64" Receiver Length: 6 13/16" Receiver Width: 1 1/4" Over All Length of Part: 27" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS: You will need your takedown screw. We will provide a brass escutcheon. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

STRAIGHT GRIP WINCHESTER 92 POST 64 STOCK & FOREND WALNUT SATIN FINISH BOYDS PLASTIC BUTT PLATE STOCK It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 15/16" Top Tang Length: 3 15/16" Bottom Tang Width: 5/8" Bottom Tang Length: 3 15/16" Stock Height at Receiver: 1 7/16" Stock Width at Receiver: 1 5/16" Overall Length of Stock:13 1/4" Measurement of Receiver Mounting Bolt: N/A Comes with Boyds' plastic buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel at Receiver: Approximately 1" Barrel Channel at End: 11/16" Receiver Edge to Center of Mounting Screw: 6 7/8" Shoulder to Shoulder: 6 11/16"Overall Length of Part : 7 3/16" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

AGILITY TACTICAL SOLUTIONS X-RING VR, .920 BARREL CONTOUR STOCK Barrel Dimensions: Point A = .920" and Point B = .920" Center to Center of Action Screws: N/A Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock comes with brass mounting escutcheon and is designed for the Factory Semi-Auto Action, measuring 6 3/16" long. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP THUMBHOLE TACTICAL SOLUTIONS X-RING VR, .920 BARREL CONTOUR STOCK Barrel Dimensions: Point A = .920" and Point B = .920" Center to Center of Action Screws: N/A Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock comes with brass mounting escutcheon and is designed for the Factory Semi-Auto Action, measuring 6 3/16" long. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE TACTICAL SOLUTIONS X-RING VR, .920 BARREL CONTOUR STOCK Barrel Dimensions: Point A = .920" and Point B = .920" Center to Center of Action Screws: N/A Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock comes with brass mounting escutcheon and is designed for the Factory Semi-Auto Action, measuring 6 3/16" long. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE TACTICAL SOLUTIONS X-RING VR, .920 BARREL CONTOUR STOCK Barrel Dimensions: Point A = .920" and Point B = .920" Center to Center of Action Screws: N/A Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock comes with brass mounting escutcheon and is designed for the Factory Semi-Auto Action, measuring 6 3/16" long. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRO VARMINT TACTICAL SOLUTIONS X-RING VR, .920 BARREL CONTOUR STOCK Barrel Dimensions: Point A = .920" and Point B = .920" Center to Center of Action Screws: N/A Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock comes with brass mounting escutcheon and is designed for the Factory Semi-Auto Action, measuring 6 3/16" long. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

LEFT HAND BLASTER TACTICAL SOLUTIONS X-RING VR, LEFT HAND STOCK .920 BARREL CONTOUR STOCK Barrel Dimensions: Point A = .920" and Point B = .920" Center to Center of Action Screws: N/A Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock comes with brass mounting escutcheon and is designed for the Factory Semi-Auto Action, measuring 6 3/16" long. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

BARRACUDA TACTICAL SOLUTIONS X-RING VR, .920 BARREL CONTOUR STOCK Barrel Dimensions: Point A = .920" and Point B = .920" Center to Center of Action Screws: N/A Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock comes with brass mounting escutcheon and is designed for the Factory Semi-Auto Action, measuring 6 3/16" long. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SS EVOLUTION TACTICAL SOLUTIONS X-RING VR, .920 BARREL CONTOUR STOCK Barrel Dimensions: Point A = .920" and Point B = .920" Center to Center of Action Screws: N/A Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock comes with brass mounting escutcheon and is designed for the Factory Semi-Auto Action, measuring 6 3/16" long. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

RIMFIRE THUMBHOLE TACTICAL SOLUTIONS X-RING VR, .920 BARREL CONTOUR STOCK Barrel Dimensions: Point A = .920" and Point B = .920" Center to Center of Action Screws: N/A Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock comes with brass mounting escutcheon and is designed for the Factory Semi-Auto Action, measuring 6 3/16" long. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

RIMFIRE HUNTER TACTICAL SOLUTIONS X-RING VR, .920 BARREL CONTOUR STOCK Barrel Dimensions: Point A = .920" and Point B = .920" Center to Center of Action Screws: N/A Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock comes with brass mounting escutcheon and is designed for the Factory Semi-Auto Action, measuring 6 3/16" long. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

BLASTER TACTICAL SOLUTIONS X-RING VR, .920 BARREL CONTOUR STOCK Barrel Dimensions: Point A = .920" and Point B = .920" Center to Center of Action Screws: N/A Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock comes with brass mounting escutcheon and is designed for the Factory Semi-Auto Action, measuring 6 3/16" long. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

LH PLAT BROWNING AB2 SSA 2PC HINGED FLOOR PLATE LH STK FBC PEPPER SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1.176" and Point B = .842"Center to Center of Action Screws: 6.66"Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need the floor plate, take down screws, trigger guard and screw from your factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a . All Rapid Fire sales are final! Nonreturnable & nonrefundable.

LH FT REMINGTON 783 LA LH STK RH ACT DBM FBC NUTMEG SATIN FINISH BOYDS PAD ATTENTION CUSTOMERS: DENTED TIP Barrel Dimensions: Point A = 1 5/64" and Point B = 3/4"Center to Center of Action Screws: 7 31/32"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.Safety and Bolt Release are located on the side of the receiver.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final!

RIMFIRE HUNTER CZ 452-2E AMERICAN SA CLIP FEED LH ACT FBC PEPPER SATIN FINISH BOYDS PAD ATTENTION CUSTOMERS: SCRATCHES AND DENTS ON BUTTSTOCK, BOTH SIDES. Barrel Dimensions: Point A = .99" and Point B = .712"Center to Center of Action Screws: 3.235"Over All Length of Part: 31.25"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need floor plate, take down screws, trigger plate and clip from the factory stock. ATTENTION CUSTOMERS: Not compatible with ZKM model variations. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

LH FT SAVAGE 112 TBR BLIND MAG STFG LH STK RH ACT FBC Forest Camo Satin Finish Boyds Pad ATTENTION CUSTOMERS: Bubbles in the finish on comb. Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page. This stock is designed for the Savage Model Blind Magazine with Staggered Feed action and a top bolt release. When you disassemble your action the magazine box will be attached to the receiver. If the magazine box stays inside of the stock when the barreled action is removed, you may need the Center Feed Model or CTF version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

HERT REMINGTON 700 SA DBM HAWKINS PRECISION M5 FBC Black Textured Paint Boyds Pad ATTENTION CUSTOMERS: Dented cheek piece Barrel Channel Dimensions: Point A - 1 1/4" Point B - 3/4" Center to Center Action Screws: 6 1/2" Comes with Boyds 1/2" recoil pad. ATTENTION CUSTOMERS: This inlet is machined to accept the Hawkins Precision M5 Detachable Box Magazine Short Action Bottom Metal. You will need to purchase the Hawkins Precision M5 Bottom Metal separately. Inlet is not milled for Hawkins pillars due to end user preference. Refer to Hawkins Precision for specifics of the M5 Detachable Box Magazine. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

SPIKE CAMP SAVAGE 93 LEFT HAND ACTION, BULL BARREL CHANNEL Forest Camo Satin Finish Boyds Pad Barrel Dimensions: Point A = 13/16" and Point B = 13/16" Center to Center of Action Screws: 3 11/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: This stock is designed for the Sav93-E/MKII heavy barrel with inlet trigger guard and floor plate. Action measures 7 3/4" long on the 93E/MKII action. Pre-93E receivers (with a lug at the back of the reciever) can be fit to our 93E/MKII stocks but will require fitting of your receiver and barrel to the stock. Minor gap will be visible on rear of stock with older pre-accutrigger actions. Older receivers are about 4 inches longer and will need to be fit. Variations in action mounting screw pillars exist between models. Do not over tighten. ATTN customers: Side mount rear peep sights will require modifications of the stock for fitment. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page, bottom left-hand corner. Part numbers for 22 LR: 100654 (Blued), 100655 (Nickel). Part numbers for 17hmr/22mag: 100656 (Blued), 100657 (Nickel). Some stocks may also require different action screws which are available through DiProductsInc: PN 13020. Variations in action mounting screw pillars exist between models. Do not over tighten. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

HERT STEYR PRO HUNTER #3 LA DBM FBC PEPPER SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1 1/64" and Point B = 45/64" Center to Center of Action Screws: 4 29/32" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This inlet is for the Pre 2024 models that have the magazine liner attached to the action. We will be You will need the front takedown screw from your stock. We will be providing the trigger guard, trigger guard screw, and rear takedown screw.. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

SPIKE CAMP SAVAGE 111 SIDE RELEASE DBM LA FBC COYOTE HIGH GLOSS BOYDS PAD It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Barrel Dimensions: Point A = 1 21/64" and Point B = 23/32"Center to Center of Action Screws: 5 1/16”Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS:  This inlet is for the side release magazine version. You will need your trigger guard with screws and side release button.  All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

SPIKE CAMP CZ 600 Range Medium Action: Center to Center of Action Screws: 5" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN Customers torque settings for the takedown screws is 25 to 35 inch lbs, over torquing may cause damage to the front magazine tab and stock. We will provide the trigger guard and front lug plate, you will used the factory takedown screws, and factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE CZ 600 Range Medium Action: Center to Center of Action Screws: 5" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN Customers torque settings for the takedown screws is 25 to 35 inch lbs, over torquing may cause damage to the front magazine tab and stock. We will provide the trigger guard and front lug plate, you will used the factory takedown screws, and factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE CZ 600 Range Medium Action: Center to Center of Action Screws: 5" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN Customers torque settings for the takedown screws is 25 to 35 inch lbs, over torquing may cause damage to the front magazine tab and stock. We will provide the trigger guard and front lug plate, you will used the factory takedown screws, and factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

LEFT HAND HERITAGE CZ 600 Range Medium Action, Right Hand Action, Left Hand Stock: Center to Center of Action Screws: 5" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN Customers torque settings for the takedown screws is 25 to 35 inch lbs, over torquing may cause damage to the front magazine tab and stock. We will provide the trigger guard and front lug plate, you will used the factory takedown screws, and factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

LEFT HAND PLATINUM CZ 600 Range Medium Action, Right Hand Action, Left Hand Stock: Center to Center of Action Screws: 5" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN Customers torque settings for the takedown screws is 25 to 35 inch lbs, over torquing may cause damage to the front magazine tab and stock. We will provide the trigger guard and front lug plate, you will used the factory takedown screws, and factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.