Rapid Fire Products

Savage® 67 (top Rec Safety) Stock WALNUT UNFINISH BOYDS BUTTPLATE These parts are designed to fit the Savage,Stevens,Springfield and Fox models 30,67,77,79,168 and 176 stocks with top receiver safety, please compare your stock and receiver measurements with those we supply.Make sure to confirm demensions with those supplied for this parts. There may be up to five variations of this model.Top Tang width - 9/16ths"Top Tang length - 1 7/16ths"BottomTang width - 5/8ths"BottomTang length - 1 5/16ths"Stock height at receiver -1 5/8ths"Stock width at receiver -1 1/2" Semi-inlet parts have been comletely shaped and 95% machine inlet. Stocks are rough sanded and unless otherwise specified, are shipped with a BOYDS' butt plate.(SEMI-INLET) stocks do require some knowledge of firearms and woodworking for installation. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

LH STERLING THUMBHOLE H&R® SINGLE SHOT STOCK & FOREND APPLE JACK SATIN FINISH BOYDS VENTED PAD STOCK Stock comes with mounting bolt that will require 7/32 allen wrench for assembly. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: N/A Top Tang Length: N/A Bottom Tang Width: N/A Bottom Tang Length: N/A Stock Height at Receiver: 1 3/4" Stock Width at Receiver: 1 15/32" Overall Length of Stock: 12 3/4" Comes with 3/4" vented recoil pad All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS: These stocks are designed for the modern style knuckle style receiver. Please see our H&R round tang stock for older tanged receiver models. FORENDIt is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: 1 1/16 " Barrel Channel Point B: 11/16 " Receiver Edge to Center of Mounting Screw: 3 5/8 " Center to Center of Mounting Screws/Magazine Tube Shoulder to Shoulder: N/A" Over All Length of Part: 9 " All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:If you are converting from a plastic forend, you will need to purchase rear mounting bracket from H&R or Brownells.These parts require fitting of your barrel. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

STERLING THUMBHOLE, CVA SCOUT V2 STOCK & FOREND PEPPER SATIN FINISH BOYDS VENTED PAD STOCK It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Top Tang Width: 11/16" Top Tang Length: 13/16" Bottom Tang Width: N/A Bottom Tang Length: N/A Stock Height at Receiver: 1 1/4"Stock Width at Receiver: 1 3/8"Overall Length of Stock: 13 7/8"Measurement of Receiver Mounting Bolt: 3 5/8"Comes with Boyds Pad. ATTENTION CUSTOMERS: You will need your factory Stock Receiver Bolt. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. Barrel Channel Point at Rear: 1"Barrel Channel Point at Front: 15/16"Receiver Edge to Center of Mounting Screw: N/A"Magazine Tube Width: N/A"Center to Center of Mounting Screws: 5 1/4"Magazine Tube Shoulder to Shoulder: N/A"Over All Length of Part: 10 1/2"It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need the factory forend Takedown Latch and the factory two mounting screws. One sling stud will be mounted on the forend. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

PH MAUSER LARGE RING #1 BARREL CHANNEL XX MAPLE HIGH GLOSS BLACK TIP BLACK GRIP CAP BOYDS PAD LOP 14" ATTENTION CUSTOMERS: TIP IS SEVERELY SCRATCHED AND A CHIP IN THE FINISH. GRIP HAS PEELING FINISH. SANDING MARKS THROUGHOUT STOCK. Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

SPIKE CAMP SAV AXIS SHORT ACTION LH ACTION FBC NUTMEG SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1 1/32" and Point B = 23/32" ATTENTION CUSTOMERS: For short action calibers; 22-250 REM, 223 REM, 243 WIN, 308 WIN, or 7MM-08 REM. When assembling, hold the barrel in the center of the channel and tighten screws. Length of Mag Box: 3 17/64" approximately Center to Center of Action Screws: 4 25/32" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety is located on the tang and the Bolt Release is on the side of the receiver. A black plastic trigger guard, screw, front mag tab, rear mag tab, and recoil lug are included with the stock. ***Stainless Steel Metal trigger guards are also available: PN 100662. They can be found on the Accessories page.*** ATTENTION CUSTOMERS: This stock is compatible with the Savage Axis II and Axis XP models. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

FT SAV AXIS DBM LA FBC FOREST CAMO SATIN FINISH BOYDS PAD ATTENTION CUSTOMERS: FINISH FLAWS/BLEMISHES NEAR FLUTED FOREND ON RIGHT SIDE. OVERSANDING TIP, ONE FOREND EDGE FALLS OFF AND IS UNEVEN Barrel Dimensions: Point A = 1 11/32" and Point B = 23/32"ATTENTION CUSTOMERS: For long action calibers; 25-06 REM, 30-06 SPFLD, or 270 WIN. When assembling, hold the barrel in the center of the channel and tighten screws.Length of Mag Box: 3 49/64" approximately Center to Center of Action Screws: 4 25/32"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.Safety is located on the tang and the Bolt Release is on the side of the receiver. A black plastic trigger guard, screw, front mag tab, rear mag tab, and recoil lug are included with the stock. ***Stainless Steel Metal trigger guards are also available: PN 100662. They can be found on the Accessories page.***ATTENTION CUSTOMERS: This stock is compatible with the Savage Axis II and Axis XP models. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final!

PLAT WIN 70 SHORT ACT 2PC FP FBC POST 64 PEPPER SATIN FINISH BOYDS PAD ATTENTION CUSTOMERS: OVERSANDING ON TIP, ONE SIDE DROPS OFF MAKING IT UNEVEN Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock will not work for the WSSM Caliber Rifles. Pre-1984 actions are based on the Long Action receiver. These stocks are designed for the Winchester? Model 70 Short Action 2-Piece hinged floor plate model with a standard factory tapered barrel. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect./p> All Rapid Fire sales are final! Nonrefundable & nonreturnable.

HERT SAV 10 TBR BLIND MAGAZINE, SHORT ACTION, LEFT HAND STOCK, RIGHT HAND ACT, CENTERFEED, FACTORY BARREL CHANNEL NUTMEG SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page. This stock is designed for the Savage Blind Magazine with Center Feed Action and a top bolt release. When you disassemble your action the magazine box will stay inside the stock when the barreled action is removed. If the magazine box stays attached to the action, you may need the Staggered Feed Model or STAGGERED FEED version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final!

PH CZ 550 AMERICAN LONG ACTION FBC PEPPER SATIN FINISH BOYDS PAD It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Barrel Dimensions: Point A = 1 7/64" and Point B = 47/64"Center to Center of Action Screws: 7 53/64”Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS:  You will need your takedown screws, floor plate assembly, and mag well. All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

SPIKE CAMP THUMBHOLE SAV 10 TBR SHORT ACTION DETACHABLE MAG FBC MAROON SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 29 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. ATTENTION CUSTOMERS:If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

PV Savage MKII BBC BLACK TEXTURED PAINT BOYDS PAD Barrel Dimensions: Point A = 13/16" and Point B = 13/16" Center to Center of Action Screws: 3 11/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Sav93-E/MKII heavy barrel with inlet trigger guard and floor plate. Action measures 7 3/4" long on the 93E/MKII action. Pre-93E receivers (with a lug at the back of the reciever) can be fit to our 93E/MKII stocks but will require fitting of your receiver and barrel to the stock. Minor gap will be visible on rear of stock with older pre-accutrigger actions. Older receivers are about 4 inches longer and will need to be fit. Variations in action mounting screw pillars exist between models. Do not over tighten. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page, bottom left-hand corner. Part numbers for 22 LR: 100654 (Blued), 100655 (Nickel). Part numbers for 17hmr/22mag: 100656 (Blued), 100657 (Nickel). Some stocks may also require different action screws which are available through DiProductsInc: PN 13020. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

RIMFIRE HUNTER RUGER AMERICAN RIMFIRE 22MAG/17HMR FOREST CAMO SATIN FINISH BOYDS PAD ATTENTION CUSTOMERS: CHIP ON TOP OF INLET ABOVE MAGWELL. VISIBLE SANDING MARKS ON THE BUTT AND FOREND. Barrel Dimensions: Point A = 55/64" and Point B = 23/32" Center to Center of Action Screws: 3 7/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety is located on the tang and the Bolt Release is on the side of the receiver. ATTENTION CUSTOMERS: You will need the rear magazine block, front magazine block, and takedown screws. We will provide the trigger guard and screw. ATTENTION CUSTOMERS: Not compatible with target model. It is only compatible for plastic/synthetic to wood conversion.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

PH CZ 550 AMERICAN LONG ACTION FBC PEPPER SATIN FINISH BOYDS PAD ATTENTION CUSTOMERS: FINISH FLAWS AND DENTS ON COMB It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Barrel Dimensions: Point A = 1 7/64" and Point B = 47/64"Center to Center of Action Screws: 7 53/64”Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS:  You will need your takedown screws, floor plate assembly, and mag well. All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

LH BLASTER RUGER 1022 .920/HEAVY BARREL PEPPER SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = .920" and Point B = N/A Center to Center of Action Screws: N/A Over All Length of Part: 26 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Comes with brass mounting escutcheon. This stock is designed for the factory Ruger 10/22 semi auto action measuring 6 3/16" long. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

CLA SAV 111 TBR DETACHABLE MAG LONG ACTION FBC PEPPER SATIN FINISH PACHMAYR PAD LASER PANEL BLACK GRIP CAP PILLAR BEDDING ATTENTION CUSTOMERS: DISCOLORATION IN LASER PANEL ON FOREND, BROWN Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage detachable box magazine rifle with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Long Action Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS:If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE LA PLASTIC MAG WELL from our Accessories page, Part No. A09160 or SAVAGE LA METAL MAG WELL, Part No. A09213. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

SPIKE CAMP THUMBHOLE RUGER ACF PREDATOR AR MAG SA FBC FOREST CAMO SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1 1/64" and Point B = 3/4" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear taked down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks recommends bedding the front and rear lugs.. ATTENTION: A relief cut to allow magazine release button clearance has been added. ATTENTION CUSTOMERS : You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimmensional differences they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. ATTENTION: The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with the Ruger Mini 30 Magazines due to the steel mag liner. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

PH BROWNING A-BOLT SHORT ACT FBC NUTMEG HIGH GLOSS BOYDS PAD ANGLED BLACK TIP BLACK GRIP CAP LASER INITIALS: LEA FONT #2 Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4"Center to Center of Action Screws: 7 1/4"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info.All finished stocks have been CNC inlet to Boyds House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

HERITAGE MOSSBERG 100 ATR SA FBC XX MAPLE HIGH GLOSS WHITE LINE SPACER BOYDS PAD BLACK GRIP CAP LASER PANEL ATTENTION CUSTOMERS: Visible sanding marks throughout stock. Slight dent on comb. Barrel Dimensions: Point A = 1 3/8" and Point B = 13/16" Center to Center of Action Screws: 4 9/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: If you are converting from a plastic stock, you will need to purchase a trigger guard from our Accessories page: ITEM # A09157, and an action screw from Mossberg directly, ITEM # 101532. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

CLASSIC SAVAGE AXIS SHORT ACTION DBM FBC Walnut Satin Finish Boyds Pad Barrel Dimensions: Point A = 1 1/32" and Point B = 23/32" ATTENTION CUSTOMERS:When assembling, hold the barrel in the center of the channel and tighten screws. Safety is located on the tang and the Bolt Release is on the side of the receiver. A black plastic trigger guard, screw, front mag tab, rear mag tab, and recoil lug are included with the stock. Length of Mag Box: 3 17/64" approximately Center to Center of Action Screws: 4 25/32" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety is located on the tang and the Bolt Release is on the side of the receiver. A black plastic trigger guard, screw, and recoil lug are included with the stock. ***Stainless Steel Metal trigger guards are also available: PN 100662. They can be found on the Accessories page.*** ATTENTION CUSTOMERS: This stock is compatible with the Savage Axis II and Axis XP models. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

VARMINT THUMBHOLE, REMINGTON® 700, SHORT ACTION, DETACHABLE MAG, FACTORY BARREL CHANNEL PEPPER SATIN FINISH LIMBSAVER PAD Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4" Center to Center of Action Screws: 6 1/2" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is inlet for the standard factory tapered barrel. These stocks are designed for the Remington 700 receiver with factory supplied detachable box magazine. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

FT RUGER AMERICAN SHORT ACTION AR MAG PEPPER SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS : You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. ATTENTION: The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

CLA TIKKA T3 DBM FBC FOREST CAMO SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1 9/64" and Point B = 45/64"Center to Center of Action Screws: 7"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.Safety is located on the tang and the Bolt Release is on the side of the receiver.AATTENTION CUSTOMERS: Steel lug will be installed in this stock.ATTENTION CUSTOMERS: This stock is compatible with the T3x model. ATTENTION CUSTOMERS: This stock is NOT compatible with the T3x Compact Tactical. ***Aluminum T3 Bottom Metal available on the Accessories page. Compatible with T3 and T3 Lite models. Part number: A09210***It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefunable & nonreturnable.

CLA HOWA 1500 MINI DBM HVY #6 BC PEPPER SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1.095" and Point B = .783" Center to Center of Action Screws: 6.785" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

PLAT REM 700 ADL LA FBC CLARO XX WALNUT SATIN FINISH LIMBSAVER PAD WHITE LINE SPACER ANGLED WALNUT TIP CAP WALNUT GRIP CAP LASER PANEL PILLAR BEDDING Barrel Dimensions: Point A = 1 1/4" and Point B = 25/32" Center to Center of Action Screws: 7 3/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Inlett for standard factory tapered barrel channel. This stock is designed for the Remington 700 Right Hand Long Action with blind magazine, loads and unloads through top of action. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

FT MOSSBERG 4X4 DBM LA FBC ROYAL SATIN FINISH BOYDS PAD ATTENTION CUSTOMERS: SCRATCH ON RIGHT SIDE OF STOCK ABOVE MAGWELL, WOOD FILL MISSED NEAR SAME AREA Barrel Dimensions: Point A = 1 11/64" and Point B = 23/32" Center to Center of Action Screws: 5 15/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. The Safety and Bolt Release are on the side of the receiver. ATTENTION CUSTOMERS: OUR STOCK WILL ONLY WORK FOR THE PLASTIC/SYNTHETIC TO WOOD CONVERSION. You will need to use the plastic mag liner from the original factory stock and the front action screw (.930"). Each stock will be supplied with the rear action screw (1.5"), "FLAT FRONT" trigger guard, and wood screw (1"). It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

CLA ENFIELD P17 MBC Claro XX Walnut High Gloss Kick-EEZ Pad Walnut Grip Cap Angled Walnut Tip White Line Spacer LOP 13 1/4" ATTENTION CUSTOMERS: scratches on grip, tip, white line stained for walnut oil, dented and finish issues Barrel Dimensions: Point A = 1 11/32" and Point B = 25/32" Center to Center of Action Screws: 8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: P-17 stocks are cut for the original military barrel channel and use the original stepped style floor plate. If you are using a straightened non-step design floor plate, modification and refinishing will be required. These are Sporter stocks, they are not cut for barrel bonds and are not intended to be used with handguard. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

SPIKE CAMP WIN 70 SA 2PC FP FBC POST 64 Royal Jacaranda Satin Finish Boyds Pad Laser Panel Pillar Bedding Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 29 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock will not work for the WSSM Caliber Rifles. Pre-1984 actions are based on the Long Action receiver. These stocks are designed for the Winchester Model 70 Short Action 2-Piece hinged floor plate model with a standard factory tapered barrel. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

PLAT HUSQVARNA MAUSER LARGE RING #1 BC WALNUT SATIN FINISH BOYDS PAD LASER PANEL PILLAR BEDDING ATTENTION CUSTOMERS: RUN IN FINISH ON BACK SIDE OF BUTT Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

HERT REM 700 ADL LA FBC NUTMEG SATIN FINISH PACHMAYR PAD LASER PANEL PILLAR BEDDING LOP 13 1/2" ATTENTION CUSTOMERS: BLACK STAIN FROM LASER IN THE BARREL CHANNEL Barrel Dimensions: Point A = 1 1/4" and Point B = 25/32" Center to Center of Action Screws: 7 3/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Inlett for standard factory tapered barrel channel. This stock is designed for the Remington 700 Right Hand Long Action with blind magazine, loads and unloads through top of action. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

CLA SAV 111 SIDE RELEASE DBM LONG ACTION FBC FOREST CAMO SATIN FINISH BOYDS PAD It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Barrel Dimensions: Point A = 1 21/64" and Point B = 23/32"Center to Center of Action Screws: 5 1/16”Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS:  This inlet is for the side release magazine version. You will need your trigger guard with screws and side release button.  All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable and nonreturnable.

PH SAV B-SERIES BBC NUTMEG SATIN FINISH BOYDS PAD Barrel Dimensions: where barrel meets receiver/Point A=.8" Barrel Dimensions: 9 inches in front of Point A/Point B= .8" Center to Center of Action Screws: 3.35" Over All Length of Part: 31.5" This Inlet will work for both long rifle and magnum action. Attention Customers: We provide the washer for the front take down screw and a trigger guard. Attention Customers: It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable and nonreturnable.

RIMFIRE HUNTER, RUGER 77/22®, FACTORY BARREL CHANNEL PEPPER SATIN FINISH BOYDS PAD ATTENTION CUSTOMERS: WOOD KNOT NEAR TOE AREA OF STOCK, PRESENT IN PHOTO Barrel Dimensions: Point A = 15/16" and Point B = 3/4" Center to Center of Action Screws: 7 1/2"Width of Magazine Well: 1 5/16"Length of Magazine Well: 3 11/32" Over All Length of Part: 29" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: These stocks are designed for the Ruger 77 Bolt Action 22 Long Rifle. Early plastic stocks will require additional mounting hardware to use our stocks. Please contact Ruger or Brownells (800) 741-0015 for the metal trigger guard and clip assembly. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect>. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

CLA WIN 70 SA 1PC FP FBC POST 64 COYOTE SATIN FINISH PACHMAYR PAD LASER PANEL ATTENTION CUSTOMERS: LIGHTER COLOR LAMINATE LAYER DID NOT ACCEPT STAIN AS MUCH AS DARKER LAMINATE LAYER. THIS IS NORMAL FOR NATURAL WOOD PRODUCTS. GRIP OF LASER PANEL PRESENT IN PHOTO Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:This stock will not work for the WSSM caliber rifles. Pre 1984 actions are based on the long action receiver.These stocks are designed for the Short Action 1 piece hinged floor plate with standard factory tapered barrel. All Rapid Fire sales are final!

HERT HOWA 1500 MINI DBM LH STK RH ACT HVY #6 BC WALNUT SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1.095" and Point B = .783" Center to Center of Action Screws: 6.785" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final!

LH PH SAV A22 MAGNUM SEMI-AUTO DBM LH STK RH ACT FBC WALNUT SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 0.92" and Point B = 0.69"Center to Center of Action Screws: 7.444" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable and nonrefundable.

FT RUGER M77 MKII HAWKEYE SHORT ACTION FACTORY BARREL CHANNEL PEPPER HIGH GLOSS PACHMAYR PAD PILLAR BEDDING LASER INITIALS: "SAW" FONT #5 LOP 14" Barrel Dimensions: Point A = 1 3/16" and Point B = 3/4" Center to Center of Action Screws: 7 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: These stocks are designed for the Ruger 77 MKII rifles with safety located by the bolt handle on the right hand side of the action. If you have the rear mounted safety, please see the Ruger 77 tang safety models. Our inlet is designed for Standard Short Action calibers, Magnum calibers will require the magazine well to be opened up. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

LH FT SAV 220 SLUG GUN LONG ACTION DBM LEFT HAND STOCK RIGHT HAND ACTION FBC NUTMEG SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1 1/32" and Point B = 55/64" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS: This is for the older style floor plate that measures 5.7875. The gun is chambered for a 20 GAUGE shotgun shell. You will need the trigger guard, floor plate/mag plate, and all take down screws from the original stock. This stock is designed for the right hand bolt action only. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect . All Rapid Fire sales are final! Nonreturnable & nonrefundable.

PH SAV B-MAG SHORT ACTION DBM FBC FOREST CAMO SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 55/64" and Point B = 39/64"Center to Center of Action Screws: 6"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.Safety is located on the tang and Bolt Release is on the side of the receiver. ATTENTION CUSTOMERS:  To assemble, you will need to use the two escutcheons and action screws from the original. The trigger guard/floor plate from original stock is not needed. We will provide you with a black plastic trigger guard. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:To assemble you will need to use the two escutcheons and action screws from the original. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

HERT SAV 10 TBR BLIND MAGAZINE, SHORT ACTION, CENTERFEED, FACTORY BARREL CHANNEL APPLE JACK SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page. This stock is designed for the Savage Blind Magazine with Center Feed Action and a top bolt release. When you disassemble your action the magazine box will stay inside the stock when the barreled action is removed. If the magazine box stays attached to the action, you may need the Staggered Feed Model or STAGGERED FEED version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefunable & nonreturnable.

HERT REM 710 LONG ACTION DBM FBC FOREST CAMO HIGH GLOSS BOYDS PAD LASER PANEL BLACK TIP LOP 13" ATTENTION CUSTOMERS: WHITE PAINT IN BLACK STAIN OF LASER PANEL ON FOREND, PRESENT IN PHOTO. Barrel Dimensions:where barrel meets receiver/Point A = 1.230"Barrel Dimensions:9 inches in front of Point A/Point B = .770"Center to Center of Action Screws: (Rear to Mid) 6.935", (Mid to Front 1.75"There are three takedown screws in this gun. Over All Length of Part: 31"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Attention Customers - We will provide trigger guard with screws, 2 escutcheons - 2 different types, rear mag tab, mag clip retainer, take down screw with washer, lug, and instruction sheet.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.